Hi, I was reading the changes and did update everything to the latest (as of yesterday). Maybe it will take a while to catch up..

Hi all, Recent updates seem to have broken my blinds setup. Clicking on open or closed gives either Error: Zigbee: Blind switch: unable to handle command "Open" or Error: Zigbee: Blind switch: unable to handle command "Close". Getting this in the log. Oct 16 10:32:15 raspberrypi npm[537 ...

Tried again this evening and it worked...not sure what the problem was.

I have got past that problem but i now get. My Car: Received (400) Bad Request.. Unexpected unless something has changed! ({"error_description":"Authorization code is invalid or expired.","error":"invalid_grant"}) I have tried resetting client secret but same error. I am missing something small i ...

Hi all,
Trying to set this up and when i get to the test piece i cannot connect to localhost.
Tried multiple times and no luck.
Any ideas what to try?

Follow up to this i never got all devices working properly. I have asked on Github but getting nowhere fast. I have posted logs up there at https://github.com/Koenkk/zigbee2mqtt/discussions/8291 Has anyone got a clue as to what is going on, hoping someone has seen this before and can help me out ...

I added what you have to /etc/monit/conf-enabled/domoticz and commented out the relevant lines in monitrc. same error, so i deleted that section and the syntax error moves it is now at the point where it has a problem with the word "Disk" in the line that reads # if failed gid "disk" then unmonitor ...

This is the line

Hi, thanks for the replies. I have tried both of the above suggestions and even though i copy and pasted them into my own file i still get a syntax error '/etc/init.d/domoticz.sh' when i check syntax. I must be missing something in setup. Is it possible to totally remove Monit and setup again from ...

Hi all, I am having some trouble getting Monit to run and would appreciate some guidance if possible. I get the following error pi@raspberrypi:~ $ sudo systemctl status monit.service ● monit.service - LSB: service and resource monitoring daemon Loaded: loaded (/etc/init.d/monit; generated) Active: ...

Hi, Just an update.
It seems that the zigbee2mqtt update hadn't worked for some reason.
Re did it and i know have all but two devices up and running.

Hi all, Following an SD card failure today i had to use a backup image to get up and running again. Since this backup was done i have added many Zigbee devices using zigbee2mqtt.Lesson learned backup more often. The one device that was on my system at the time is there and works fine. However when i ...

Ah, i have to admit i do not know how to do that.
Off to google it.

#!/bin/bash #setup host=192.168.1.150 port=8080 username=xxx password=xxxx pingidx=83 downloadidx=82 uploadidx=84 # no need to edit speedtest-cli --simple > output.txt ping=$(cat output.txt | sed -ne 's/^Ping: \([0-9]*\.[0-9]*\).*/\1/p') download=$(cat output.txt | sed -ne 's/^Download: \([0-9 ...

Hi all, trying to set this up on my Domoticz. However when i try to run the script in Thonny to test it i get a syntax error on the IP address of my Domotcz machine. See below. I have no clue as to what would cause this, Any ideas? Thanks. Python 3.7.3 (/usr/bin/python3) >>> %Run speedtest.sh ...

Hi all, I purchased a few of the Lidl Zigbee devices. Colour bulb, LED strip and 2 of the smart plugs. Bulb and LED strip integrated into Domoticz no problem. The smart plugs are driving me a bit nuts to be honest. One seems to pair but not show in devices the other gives an error. Domoticz log has ...

after much poking about it turns out that a bit of tweaking was required.
Added it by following this viewtopic.php?t=29652

Slight update to this, Updated zigbee2mqtt and it now is reported correctly in the Domoticz log but does not show in Devices.
One step forward one step back.

Hi all, I just received a Gledopto LED strip and mini controller, i can get it to show up in Domoticz but when first connected shows as a motion sensor. I can change this to Dimmer but get no option for colour etc either way it does not respond as any type of switch. I have tried deleting it and re ...

I would like to thank Madgeni, the above and a bit of one to one tuition and it is all working well.
Excellent support.