hello, I can't iclude my FGBS-001 Universal Binary Sensor in my zwave network. I am running latest stable domoticz on RPI 2 + Razberry (more than 30 zwave devices). I am using a DC12V - 200mA charger, tested with a led strip (works fine), but i can't include the FGBS-001. I have tried GND + P and ...

Can’t believe it was that easy! Had the exact same problem.

Matt

"You need a power-supply to power it (any voltage between 9V and 30V DC); its power consumption is too high for a 9V battery to last even 1-2 days (we measured around 160mW @16V DC input with one DS18B20 temperature sensor connected and with very strong Z-wave controller signal strength)" https ...

Thanks, that certainly explains the behaviour! I had a read through the sub/slave section of the manual and it does start by saying that this is a difficult concept but then unfortunately doesn't explain the purpose of the function in a short and to-the-point sentence such as yours.

Regards,
Mattias

I've just tried the same thing with a Nexa RF transmitter mapped as a sub device under a Fibaro dimmer by following the steps on page 28 and 29 in the manual. When operating the remote on and off buttons both the sub-device and the main device change status to On in Domoticz but no command is sent ...

No that's most likely the tamper switch which triggers if the unit is removed from its base.

As this sensor is battery powered and asleep 99% of the time there's no way to connect to it in order to trigger the siren on demand.

Matt

Looks promising and could be very useful if for instance the laundry room is in the basement. I hope there will be a way to interact with the appliances directly to avoid dependency on a central server on the web and an internet connection. Also it reduced the risk of getting hacked, don't want my ...

Check if you have forms-based authentication enabled instead of basic auth in Domoticz settings.

Or you could send a basic auth header as described here:
https://www.domoticz.com/wiki/Domoticz_ ... horization

Matt

Go for gold team Sweden!

/Mattias

Another plus for the USB stick is that you can remove it and press a button on it when next to a wired in device for pairing etc. Bit tricker with an on-board unit.

Matt

+1

That's good news!

Isn't the external tamper switch under the sensor identical to the button inside the casing? Either way, both are labelled TMP in the manual: http://www.fibaro.com/files/instrukcje/eng/DoorWindowSensor%20FGK-101-107%20ENG_v21-v23.pdf However, I'm pretty sure I kept the sensor flat on a table with ...

I get the same.

Some session variable in the website that's got lost?

Matt

Hi I just added three of them to my setup and they showed up just fine after enabling the protocol in Domoticz. I'm in the latest beta version of Domoticz and Type 1 ver 1001 of RFXtrx. The only drawback is they are very chatty and with three of them transmitting it looks like they are blocking some ...

Try:

if(otherdevices['Kitchen Motion'] =='On' or otherdevices['Hallway Motion'] =='On')

Here are two options

Download 'curl' for Windows here:
https://curl.haxx.se/dlwiz/?type=bin&os ... cpu=x86_64

Or try and run the Windows PowerShell command 'Invoke-WebRequest':
https://technet.microsoft.com/en-us/lib ... .620).aspx

I wish I had that as a number... don't even think it's a valid phone number.

Here are my scripts to send a snapshot from a Foscam IP camera to my phone and watch: iMessage.sh #!/bin/bash wget http://192.168.0.101:8080/camsnapshot.jpg?idx=2 -O /tmp/cam.jpg osascript ~/iMessage.scpt +990011223344 "Subject: Door open" "/tmp/cam.jpg" iMessage.scpt on run argv set theAttachment ...

Very cool!

I had to add 'of service...' to the iMessage command though to make it work: