Hi,

In the past, Oregon made excellent temperature/humidity sensors which were on AA batteries. They lasted several years.
Then, they replaced it a few years ago by a newer model working on AAA. Now the sensor runs out of juice after approximately one year. With 14 of these everywhere in the home ...

I had the same need. I purchased an extension to my Hormann garage door opener which provides input/output dry contacts for getting the door state and triggering open/close. And I added the Fibaro Smart implant inside. This means I have an input to check the door state, and two inputs for opening ...

Hi,

I have purchased this switch from NodOn for controlling various stuff at home, and successfully included it to my network.
In Domoticz, I have 4 switch devices (one dimmer and three on/off).

Now I have a few questions:
1) Is the dimmer vs on/off device type a feature, allowing to dim with one ...

Hi,

I have installed a Qubino mini dimmer, and everytime I switch it from Domoticz, this results in three event triggers instead of one. For instance, if I switch it on, I get three device events (for instance in dzvents)
- First one with state "On" immediately when I turn the switch on
- Another ...

I had the same after upgrading to the latest stable domoticz. This corresponded to a Fibaro Door Sensor, and it wasn't working anymore. So I switched back to the previous version... Latest "stable" is extremely crappy regarding zwave.

Hi,

I have a Z-Wave dimmer. When I switch it on and off in Domoticz, it dims to the corresponding value. On the switch interface, I can see, for instance if I switch it off:
- Immediately after clicking, it goes to the "off" state.
- Shortly after, it goes back to the "on" state, probably because ...

Hi,

Since yesterday, my Fibaro Door Sensor is not updating anymore in Domoticz.

In the ZWave node list, it's marked as "sleeping" (moon icon). I see it has not been seen since 36h, while the Wake-Up interval is 12h, and I've opened an closed the windowseveral times. However, when moving the ...

Considering all the reported issues/bugs, this one should IMO be renamed "dumb implant".
Well, I have a qubino dry relay that drives open/close and S2 input reports status. This one have config restored on power outage.


The garage opener has 24V power source inside the extension box, so the ...

Why would you even want to open a door to your home with domoticz?


It’s my garage, not my home. You can’t access the home from it. And I want to open it to guests when they arrive.

And no, I would not let a zwave dumb implant open my home. My two home items not connected to domoticz are the ...

Hi,

I have a bunch of Oregon Temperature and Temperature/Humidity sensors at home, models THN132 and TGHN132. These models were very good, as they work on a single AA battery (cheap, lasts several years at any temperature with a lithium one). Plus the THN132 works down to -30°C, which enables uses ...

Hi,

One of my temperature/humidity sensors, an Oregon TGHN 132, suddenly stopped being updated in Domoticz, while the battery was recent, and the LED was still flashing every minute. I tried to move it close to the receiver, without success. Resetting it fixed the issue, but this created a new ...

There is no such option controlling action on Power Up.

I contacted Fibaro, they acknowledged that relays shortly close at power-up. Which means, that the use in a Garage Door, although recommended in the manual, is totally unsecure.

Hi,

I'm awakening this thread as I got no answer... I can't believe there are no recommended AC/coolers that can be easily integrated into Domoticz!

At least, I need to switch AC on/off. And best, would be controlling temperature, fan, etc...

Thanks for advices!

Hi,

Yes, I know these two workarounds (script and/or second switch). I just wanted to mention that a thermostat with mode selector button would be super helpful for many, especially on large homes with lots of switches.

I think I will use an additional switch and start thinking into designing my ...

Hi,

I have 8 rooms, each one has a thermostat (a virtual device in Domoticz). dzVents scripts control heating, and also control the thermostat setpoint across the day.

Sometimes, I would like to set the temperature manually for some time. There is no simple way, I could add a switch for each room ...

Hi,

I have added a Fibaro Smart Implant to my garage door controller. It works very well for opening, closing, and retrieving the door state, using two outputs and one input.

However, I noticed after a power cut that when the power goes back, the door opens... And this happens only with the Fibaro ...

Hi,

I have three independent devices (Z-Wave) for my garage door : one push switch for opening, one push switch for closing, and one door sensor for state feedback.

Is there any way I can have a nice blinds/rollershutter device grouping the three instead?

Thanks!

Hi,

Thanks for the replies. I will contact the OZW github team for more advice.

When you say:

Such node should not even be able to relay others. If they claim being able to do so, it's a bug!

Were you mentioning my devices or the post from someone else?

And also, apart from my zwave radio ...

I just changed my script so that it only toggles one switch at a time, with 10 seconds interval.

It seems to be maybe better, but I still have errors:
2019-11-19 17:52:10.219 OpenZWave: Domoticz has send a Switch command!, Level: 0, NodeID: 22 (0x16)
2019-11-19 17:52:20.217 OpenZWave: Domoticz ...

Hi,

I have tried the "heal network" already, without improvement. I also plugged the controller with an USB extension cable, in order to avoid interference with nearby wifi stuff.

I have checked the network topology, everything is connected, but some devices only have 2 connections over 20 devices ...