Xiaomi Smart Home Suite (very cheap) compatibilty?

[matteos1]

yes i try but o don't know if the variable is off when the door is close or "close"

[sam329]

Any news? Is it possible to control Xiaomi devices with Domoticz? It would be great

The same question for me too man!! But I have seen so many people http://www.domoticz.com/forum/viewtopic ... 4&start=20 opting for Neato XV Pro because of easy monitoring with domoticz and the communication speed.

What about the Xiaomi???

[Oleg]

I believe they are the same except for a different brandname (Aqara vs. Xiaomi)

at me the square device was defined incorrectly - temperature and humidity have identical ID and pressure of another with type "general". Also, the battery level is not displayed

[chatainsim]

i'de like to create a scene where when i close a door with xiaomi door sensor one light is on and when the door is open light is off.
how i can i make it possible??
thank you

Events -> Lua, device:

Code: Select all

commandArray = {}
if (devicechanged['Door'] == 'Closed' and otherdevices['Xiaomi RGB Gateway'] == 'Off') then
    commandArray['Xiaomi RGB Gateway']='On'
elseif (devicechanged['Door'] == 'Open' and otherdevices['Xiaomi RGB Gateway'] == 'On') then
    commandArray['Xiaomi RGB Gateway']='Off'
end
return commandArray

[matteos1]

i'de like to create a scene where when i close a door with xiaomi door sensor one light is on and when the door is open light is off.
how i can i make it possible??
thank you

Events -> Lua, device:

Code: Select all

commandArray = {}
if (devicechanged['Door'] == 'Closed' and otherdevices['Xiaomi RGB Gateway'] == 'Off') then
    commandArray['Xiaomi RGB Gateway']='On'
elseif (devicechanged['Door'] == 'Open' and otherdevices['Xiaomi RGB Gateway'] == 'On') then
    commandArray['Xiaomi RGB Gateway']='Off'
end
return commandArray

hy thank you
could see this picture and transform in lua?

Catturablock.PNG (89.01 KiB) Viewed 3251 times

[chatainsim]

i'de like to create a scene where when i close a door with xiaomi door sensor one light is on and when the door is open light is off.
how i can i make it possible??
thank you

Events -> Lua, device:

Code: Select all

commandArray = {}
if (devicechanged['Door'] == 'Closed' and otherdevices['Xiaomi RGB Gateway'] == 'Off') then
    commandArray['Xiaomi RGB Gateway']='On'
elseif (devicechanged['Door'] == 'Open' and otherdevices['Xiaomi RGB Gateway'] == 'On') then
    commandArray['Xiaomi RGB Gateway']='Off'
end
return commandArray

hy thank you
could see this picture and transform in lua?
Catturablock.PNG

It's too small to read text.

[deennoo]

Any news? Is it possible to control Xiaomi devices with Domoticz? It would be great

The same question for me too man!! But I have seen so many people http://www.domoticz.com/forum/viewtopic ... 4&start=20 opting for Neato XV Pro because of easy monitoring with domoticz and the communication speed.

What about the Xiaomi???

Have a look to https://github.com/rytilahti/python-mirobo

That tje n'est python lib to drive Xiaomi wifi device, dev are working hard and add new device/function every day. I manage to drive my Xiaomi Philips ball led with this.

Python plugin for robot vaccum use the same lib (an older version) his way to run looks the best one, just need to be adapted for other device.

[matteos1]

Cattura.PNG (123.18 KiB) Viewed 3221 times

i think is better

Events -> Lua, device:

Code: Select all

commandArray = {}
if (devicechanged['Door'] == 'Closed' and otherdevices['Xiaomi RGB Gateway'] == 'Off') then
    commandArray['Xiaomi RGB Gateway']='On'
elseif (devicechanged['Door'] == 'Open' and otherdevices['Xiaomi RGB Gateway'] == 'On') then
    commandArray['Xiaomi RGB Gateway']='Off'
end
return commandArray

hy thank you
could see this picture and transform in lua?
Catturablock.PNG

It's too small to read text.

[chatainsim]

Cattura.PNG
i think is better

hy thank you
could see this picture and transform in lua?
Catturablock.PNG

It's too small to read text.

why don't you try to translate to lua then ask for help if you are stuck ?

[matteos1]

Ok

[LeonvA]

Hello,

I have bought a Xiaomi gateway in China last week but it doesn't connect to Domoticz.
I can control the gateway and read the status of my temperature sensor in the Mi Home app.
I've enabled LAN Communication protocol in the Mi Home app and wrote down the password.
Then I added the new hardware in Domoticz with correct IP address, port 9898 and the correct password.
But then I can't see any new devices in the devices tab.
I've also tried it on a new installed raspberry pi with domoticz on a stand alone network but also no result.

anyone who can help me?

Thanks,
Leon

What is you Fw version please ?

I've got it to work.
I used an older version of the mi home app and now it works.

[chatainsim]

Ok

It's not because I don't want to help, It's because it's the best way you to learn lua
I'

[matteos1]

Ok

It's not because I don't want to help, It's because it's the best way you to learn lua
I'

Yes i know but only this time

[ratjenl]

Well i finally received my Xiaomi gateway and added it to domoticz.

I also ordered two door/windows sensors to use it as an alarm. With the mii home app it works very well and when i put the alarm "on" it immediatly plays sound from the gateway. Is there also a way to use these sensors inside domoticz so they send the alarm to the gateway ? I tried searching google and this forum but can't find what i am looking for. Is there anybody that can help me/point me in the good direction ?

thnx

[pvm]

ratjenl
Do you have these devices available in Domoticz? Then you should be able to play a sound using blockly, some instructions on https://www.domoticz.com/wiki/Xiaomi_Gateway_(Aqara)
Did you see those? Does that help you?

[Wob76]

I just added a few zigbee power sockets to my setup, they are working fine and reporting power, on my utility graph I only see power usage and energy usage, apart from an odd "spike" on energy usage it seems to report "0", is anyone else experiencing this?

chart.jpeg (45.62 KiB) Viewed 3071 times

[Wob76]

I just did a test with it set to "computed" and I now see results in the "Energy Usage", is it possible to have these devices set to computed when they are created by the plugin?

[Stanleyk]

Hello,

I add yesterday xiaomi home to domoticz and working well. I have gateway, 5xdoor contact, 1xbutton, 2x motion sensor. and also 2x IR transmitter but this I dont see in domoticz. have anybody this working ? In MiHome aplication is working TV, AC, HomeTeather. But MiHome fo IR is in Chinese language
I am waiting for wall switches, light bulb and thermometers.
How I can control the classic lights ? Have somebody any relays what is definitely working (433 or wifi) ?

[DannyElfman]

Hi,
Does anybody know if the Xiaomi Aqara flood sensors are working with one of the latest Domoticz beta build ?

I cannot find anything on github ( https://github.com/domoticz/domoticz/co ... ateway.cpp )

[Coldman]

Hi,
Does anybody know if the Xiaomi Aqara flood sensors are working with one of the latest Domoticz beta build ?

I cannot find anything on github ( https://github.com/domoticz/domoticz/co ... ateway.cpp )

I don't know if there is one in Domoticz. It's just a water presence so I think that just 1 or 0 it's ok lol.

I think there is support for smoke alarm and gas alarm, i think this is the same, but water alarm

I could add it the same as the smoke alarm no problem, but hoping someone can suggest a more appropriate device.