If you have Z-Wave, you could try using the Fakro device.
https://www.momotica.nl/zwave-sensoren/ ... am-zws230/

Take a look at the smoke sensors from POPP. They use a good brand for the smoke sensor (Ei Products) and they installed a Z-Wave module inside the sensor. The smoke sensor has a build in battery and the Z-Wave module uses it own battery. https://www.momotica.nl/zwave-sensoren/zwave/melders ...

Why not using the 0-10volt dimmer from qubino?

I'm using it in my buva installation and there is no need for any other components or external power supply.

https://www.momotica.nl/Qubino-Flush-Di ... -Wave-Plus

Nice project; thanks for sharing! I just finished building the console. What I notice is that the buttons on switches (Timers, Notifications) consume a lot of space. These buttons are not visible in the pictures posted by the TS. Can these be removed somehow? Add the switches to the dashboard ...

How did you connect it? Can you still use the original wired remote?

hyla wrote:Yep, two separate power supplies ...

Christoph

Try if is works better when you connect it directly to you pi.

Some USB sticks don't work well when they are connected by a hub of even an USB extension cable.

I selling the Transcend cards for over a year now and haven't heard complains.
8GB: TS8GUSDC10
16GB: TS16GUSDC10

There is a list:
http://elinux.org/RPi_SD_cards

Do you use a separate power supply for the USB hub?
Could be that your raspberry hasn't got enough power for the UZB1

Please do the following: Go to Setting > Hardware > Setup (at the zwave controller) > Node management > Control panel Once your there. Press on the Dimmer 2 > select Configuration At the parameter: Force auto-calibration: select Start auto-calibration of the load WITH Fibaro Bypass and press Submit ...

You can also use 127.0.1.1:8080 in the domoticz.sh script. Then there is no need to edit the script...
It works for me

Try set setting number 2 to 75 for now.

then press the button at the bottom of the page. setting should me stored to the dimmer.

Test your dimmer, if it's still the same try set the max dim level lower.

Set the max dim level in the dimmer settings. Thanks so much! Where do I find the parameter that you say? Could this be? 2. Maximum brightness level: (%) (attuale: 80) Parameter is set automatically during the calibration process. Options for changing parameter 2-99. Default 99. Last Update: 2016 ...

Set the max dim level in the dimmer settings.

Is it possible to connect the FGD212 directly to the lamp and not having a "physical switch", my plan was to use WallC-2 http://www.z-wave.me/index.php?id=30 as the main controller, and domoticz as secondary/automatic controller. But as i read more about it seems like my plan aint working, But on ...

Try to install the fibaro dimmer without the blue wire. There can be some fluctuations on the blue wire.

Did you enable "accept new hardware" in settings?

still lots cheaper then a razberry i suppose ? Amd also much more flexible I was hoping to keep using my current raz. So that is why i say it is more expensive. More flexible? What are the benefits? I saw you can Carry it to the proximity of a node for inclusion purposes, are there any other ...

u01pei wrote:@mbliek:
Did you make a typo? You talk about a new Pi 2B. Did you mean 3? Because that is Where the problem occurs


Verzonden vanaf mijn iPhone met Tapatalk

Oeps, yes I mean the 3B

New Pi 3B works fine here with Aeotec USB Stick GEN5.
With latest image, clean install.

Did you try restarting your pc? Or at the hardware section, select the rfxcom and press update. Do not remove the device or every device will be removed that uses the rfxcom.