PhB76 wrote:Hello melgi
Can you tell me where to find this update?
Philippe

Hi phb76,

It's on the official Asustor forum in the Domoticz section.

melgi

Verstuurd vanaf mijn SM-G986B met Tapatalk

UPDATE: father_mande compiled a new version 2020.2.1 of Domoticz and with this I could get my Harmony Hub finally working again! I did enable XMPP the other day, but with the old version it didn't work. With version 2020.2 it works. Hi All, When I try to add my Harmony just like in the wiki, I don't ...

Yes! My issue has been resolved with the new Domoticz APKG for Asustor! See here: https://www.domoticz.com/forum/viewtopi ... 80#p248780.

Yes! Philippe *father_mande" created a new APKG for the Asustor Nas with the recent 2020.2 of Domoticz. I installed it yesterday and after disabling/enabling the Xiaomi Gateway, it's working again together with all my humidity sensors and automation scripts! So I don't have to manually switch my WTW ...

@rrozema, Thanx for your reaction! I put the ip address as a place holder (111.111.1.x), as I didn't know if it was custom to put ip address here in this forum. MY BAD! But the ip address of the gateway is 192.168.1.175. I have the ip address bined to a fix ip address through the mac address ...

Hi all, I automated my WTW installatie by putting a Fibaro two way relay between the switch (3 standenschakelaar) and the WTW unit for a double rocker switch. In my bathroom I have two Xiaomi Humidity sensors for my bath and shower. I then programmed the relay switch to switch to speed 2 or 3 and ...

Hi all, I automated my WTW installatie by putting a Fibaro two way relay between the switch (3 standenschakelaar) and the WTW unit for a double rocker switch. In my bathroom I have two Xiaomi Humidity sensors for my bath and shower. I then programmed the relay switch to switch to speed 2 or 3 and ...

I have an issue with my Domoticz installation. Domoticz ran perfectly on my NAS for years, until I upgraded to the recent Beta after the 2020.1 release. From then on Domoticz didn't work anymore. So I tried to go back to an earlier version and reinstall my database from a backup. I'm now running ...

My water meter has just been replaced by an exact water meter as posted in this thread. I'd like to tinker a bit with the water meter sensor. My only problem is I don't have a raspberry pi, but an Asustor NAS running my Domoticz installation. How can I connect the inductive meter to my NAS? I was ...

I finally received my 6 Aqara TBH sensors. I want to place them in the bathroom, bedrooms and also one in my son's terarium. Regarding the rooms: what is a good position to get reliable temperature readings? I remember reading somewhere that a thermostat should be placed about 1.5 m from the floor ...

So I bought a second hand Xiaomi Gateway and installed it today. Everything working fine. Next up is to add a couple of humidity/temp/airpressure sensors around the house and see if I can get that working.

Martin, If you try a similar solution as described in this post https://www.domoticz.com/forum/viewtopic.php?f=44&t=24626 and this post https://www.domoticz.com/forum/viewtopic.php?f=44&t=24622&p=190270#p190207, I think you might be able to do this. Just be sure you have an RFXcom firmware that can ...

I still can't get this to work :-(. THIS SCRIPT DOESN'T WORK FOR ME: return { on = { timer = { 'every 2 minutes on sat, sun, mon, tu, wed, thu, fri' } --timer = { 'at 10:00' }, httpResponses = { 'nextF1' } -- matches callback string below }, data = { nextF1 = { initial = nil } }, execute = function ...

I just read about the Xiaomi Smart Home Suite products. They look slick and affordable. As they use the Zigbee protocol I have the following question: - Can I use the Xiaomi products with my Philips Hue Bridge or do I need to buy the seperate Xiaomi Mijia Upgrade Version Smart Home WiFi Remote ...

Brutus, thanx for your reply. Will try that. In my post I made a mistake. The "F1" is actually the Dummy I created in the Hardware section. On this hardware I created the said virtual text sensors.

Verstuurd vanaf mijn SM-G955F met Tapatalk

I have extended the qualifying results to a top 6 . Max doesn't always qualify in the top 3 like today ;) return { on = { timer = { 'every 20 minutes' }, httpResponses = { 'nextF1', 'qualyF1' } -- matches callback string below }, data = { nextF1 = { initial = nil } }, execute = function(domoticz ...

Today's qualifying result don't show to me neither.

Verstuurd vanaf mijn SM-G955F met Tapatalk

Thanx for the clear explanation! I thought I'd try this and created my first virtual sensors and creating my first dzVents events using your code worked like a charm!

It worked! It worked! You're a hero Jonathan! Thanx! All my blinds are controlled through Domoticz now! Will update my post and refer to your solution!

Awesome Jonathan! Will try this solution this weekend. If it works with me I'll update my post as well and hopefully can help others with this as well.

Btw you're no newbie mate when solving this! I say you're a pro [emoji6]

Verstuurd vanaf mijn SM-G955F met Tapatalk