Thanks for the warning @FireWizard! Came here to find a solution for the "bug" and it turned out to be a feature

What is your topic name in Domoticz mqtt Autodiscover config? Should be zigbee2mqtt as it looks like it from your mosquito log. Default is homeassistant (also for zigbee2mqtt) so you have to change that. Ah, I should rename the Auto Discovery Prefix of the MQTT Auto Discovery Client Gateway with ...

@quazar did you add a new MQTT Autodiscover gateway that looks at zigbee2mqtt topic? See the zigbee2mqtt wiki https://www.domoticz.com/wiki/Zigbee2MQTT#Alternative_2:_Use_Domoticz_MQTT_Autodiscover yes, I did add the autodiscover gateway and enabled homeassistant under zigbee2MQTT --> settings ...

I use localhost. When I use the non-autodetect MQTT version, Domoticz can receive data using mosquitto_pub -h localhost -m '{ "idx" : 384, "nvalue" : 39, "svalue" : "270" }' -t 'domoticz/in' No data seems to be going to domoticz/in automatically according to MQTT Explorer. Can that be the problem?

I am switching to Zigbee2MQTT and Zigbee2MTQQ is running fine Zigbee2MQTT log: info 2023-01-09 17:26:34MQTT publish: topic 'zigbee2mqtt/0xa4c138ec38ecd7de', payload '{"co2":363,"formaldehyd":4,"humidity":53.5,"linkquality":116,"temperature":18.8,"voc":1}' info 2023-01-09 17:26:34MQTT publish: topic ...

Great, a small howto for Dummies would be much appreciated...

My OTGW works great in combination with a ThermoSmart thermostat. However, in the log I do get a error 02 message every few minutes. I do have a NodeMcu installed and connected a 12v power supply. This error 02 should indicate that the communication with my Calenta ACE heater is not exactly 1.25v ...

Kind of n00b question: on the Pi3 you need to disable onboard BT if you use a Razberry. Is there a way to use a USB dongle so both Razberry and BT can work simultaneously?

Not sure, sorry I have the E version. My RFlink does not seem to detect the CD17 though!

The Kerui CO detector works via rfxtrx433@lightning4.

Still does not seem to be fixed? I can't see my OWL but it used to work a year or so ago...

Have you tried any of them? Looking for a natural gas sensor as well!

Solved: I had to install zwave.me to be able to first exclude the devices. Afterwards they could be included by zwave.me and by openzwave!

I've reinstalled my Pi2 from scratch using Jessie as a basis. Domoticz works fine accept for OpenZwave. I've hard reset the Razberry in Domoticz. Some devices are recognized (Danfoss thermostats, Eminent E27 light switch) but others are not (Eminent EM6552/Everspring AN158 on/off switch and EM6551 ...

Strange! I've reset the Zwave.me on my RasPi and try to add my Z-wave devices again. Most of them can be included, but the following devices are not found: Everspring AD142 Plug-in Dimmer Module Everspring AN1582 Wallplug with energy consumption Should I install the open z-wave libraries? On my ...

Sorry for my question! The Razberry was not properly configured (e.g. not linked to /dev/ttyAMA0 yet in the Hardware settings menu), after that my Open-Z-wave network was up again! So, i000: the Razberry should be detected once you've selected the right port (/dev/ttyAMA0 in my case). I do not know ...

Because of issues with my raspi setup, I decided to reinstall the system. Where are the Razberry/open z-wave settings stored? Copying the old domoticz folder over the new one does not restore the z-wave setup. It's also not backed up as part of the Domoticz backup... Is this stored somewhere else on ...

Renkforce RF101 is cheap and works well with the rfxtrx433.