Looking at preparing for the summer with some automation for the garden and was wondering what the general experience are with the water valve Sonoff SWV-BSP; primary concern is how stable is it and if it does loose connectivity with the signee gateway will it then go int failsafe mode and close the ...

Thanks for the input and it would be great to get proper confirmation about failsafe if it's either low on battery or if it doesn't have any contact with the signee gateway. It sounds like that it's very stable and that it hasn't caused any issues in general.

With regards to the outdoor faucet if ...

What is the average battery time for these units and what kind of batteries are you using; alkaline, lithium or rechargeable batteries? The biggest worries in that it won't automatic close the valve when supposed to and assume that if runs out of battery or can't communicate with the gateway (in ...

Typically, for what ever reason, receive a few error in the Dz log ref to Philips Hue which Dz has been setup to communicate directly with the Philips Hue gateway and on the Philips side everything works as expected, so not sure what to look for based on the following error message:

2024-02-15 17 ...

Yes, works fine, I ended up getting the Aeotech gen 7 stick and the zwa012 sensor (pro version) which works as expected and without problem with Dz and zwavejsui in a container setup.

There are several threads talking and asking about which alarm control panel/keypads (also ref. to zwjs config DB ) that Dz supports and what to opt for. Also, when searching for never devices which supports S2 security the list seems quite short. So what devices are there which supports S2 security ...

Fair enought and happy to do so, then it's just matter of of which alarm control panel one should opt for. I'll open a new thread for this discussion.

Ok, thats helpfull, unfortunalty for me I see that Domoticz doesn't support Alarm control panels. Is there any kind of priotized roadmap to pick up more device categories?

I've been running with the new Aoetec 700 series stick for well over a month now with 25 zwave devices and so far no problem. Additionally, zwave-js-ui also now supports firmware OTA as well (upgraded to firmware v7.21.0 using the OTA) which is huge improvement compared to how how the upgrade ...

As topic asks, is the assumption that if ZwaveJSUI device database indicates that it support specific hardware that it can be assumed that Domoticz will support the device fully or partial?

Based on that zwave-js-ui supports the Ring Keypad v2 (writeup for HA) - does Domoticz support it as well?

Interesting script and something to test; but curious about physical keypads; what are you guys using?

What zwave keypads would be th recommend choice if one would buy something today?

How did it go this plugin - was the issue ever solved? While it would be nice to get snapshots from the unifi cams it would be more of a primary interest to be able to collect alerts when the unifi protect alerts of 'intruders'.

If you have a meter with S0 output, you can interface it using a DomBus module: they are designed for Domoticz and are very reliable.
https://www.domoticz.com/wiki/Creasol_Dombus


Re-opening this request again since my S0 Pulse readers from SOS Solution just isn't stable enough as they keep ...

Normally you would connect an esp or something similar to those pulse counters and send the data to the Domoticz server.

What would be a recommended setup for retrieving pulse counter data via esp? I'm currently using the S0 Pulse Meters from SOS Solutions which are far from stable as the stop ...

Based on the default volument mounting, ./config:/opt/domoticz/userdata and I've pulled themse down from Git to themes to ./config/www/styles but neither of the templates ( aurora and machinon ) that I've tried shows up under Settings/Theme option.

Also, beside the above volume, I also have ...

Was you ever able to get any of the above mentioned keypads to work with Domoticz?

After the changing parameter 100 to 'binary switch' for the I2 one have to exclude and then include the Qubino unit to have z2jsui to detect the additional virtual switch. Unfortunalty what I wanted was to have the same behavious as the I1 switch which is mono-type. So while it worked fine to get ...

Does zwave2mqtt support the usage of Qubino Virtual Switch (Input 2 Switch) which can be used to turn on a specific group/device? Configuration settings 100 allows to set the 'Enable / Disable Endpoints I2' to 'Binary Sensor' but not even sure if this is correct or whether it's not supported by z2m ...