Thanks a lot! I know it wasn't that complicated. I hope I'll remember this next time....

Oops, it was quite a a while since I made the configuration, so I had to check this up.

On the hardware tab i find this device:
Zigbee2MQTT Plugin

so I guess I'm using the plugin. And I'm running 2021.1 release of Domoticz.

I have Domoticz running on a RPi and managed to add ZigBee support with Ziqbee2mqtt. And I have a few ZigBee devices connected. Among those an Ikea Tradfri E1603 outlet. Everything works fine. But now I would like to add one or two extra Ikea Tradfri E1603 outlet devices and I can't remember how I ...

I have two RPI's with Domoticz. One is configured as a remote Domoticz system. By I can display all needed devices in my master Domoticz system. Now I have added a CC2632RB stick om my slave and I run the Zigbee2MQTT plugin. By this a whole a new world has opened up! Zonoff SNZB-02 temperature ...

Seems to be just one thread about this plugin, so it might be a long shot get through this way....

I'm new in the Zigbee world but not with Domoticz. Decided to try out some Zigbee stuff since I'm extremely tired of 433MHz devices. I have added a cc2652 dongle to my Rasp, installed zigbee2mqtt ...

I've just start to dig into the Zigbee world. Today I'm using Domoticz with 433Mhz temp sensors and power plugs, but I´m sick of the lousy reliability the one-way 433Mhz communication protocol provides. Temp sensors work quite well, but it's a nightmare to replace batteries since this will create ...

No, I can't see anything in the log when I try to erase a single datapoint. I have a few other Rasps in my house in my "production>" system. On those systems I can delete single datapoints in a temperature graph. I don't have any utility devices on those, so I can't verify if this works for anything ...

I've started to play around with a water meter connected to S0 meter USB interface. I did not fully get how to use the Counter divider to begin with, and by that got a few days of bad data. I would like to clear all data but I can't figure out how to do this.I found a post with a hint you should be ...

You need to configure the pins at boot. I have made an update to /etc/rc.local. In my case I have defined a shell script with the following commands and just execute this script by the end of rc.local.

#! /bin/sh
#-----------------------------------------------------------------------------
# Init ...

Maybe you should try another web-browser. This sounds weird, but sometimes the browser creates problems with Domoticz. I think it is cache or cookie related. For instance, try with Edge to see if this helps.

Well, I see this check box in my configuration. This is enabled, but to be honest I don't know what this is used for. In my case this is enabled and I add my switches manually on the switches tab. I think this thread should be moved to Bugs and problems. Maybe you can make a new post in that forum ...

Hm, I'm a bit confused here. I doubt you need to enable this python plugin to make this work. In order to just have a switch reflecting the status of an input pin, you should first of all add a new HW device - Generic sysfs GPIO. You also need to configure which pins you should use for this system ...

Thats my impression, but I will check this more thorough next time I visit my summerhouse. This will not happen in near time, more likely in a couple of weeks.

I have a feeling there is some sort of mismatch between the Rfxcom and the Nexa device. I don't know if it is RF related or the protocol. But I find it strange the Nexa remote ALWAYS works even if I'm far away from the switch device (+30m and at least one wall in between), but the Rfxcom ...

OK, sounds like a reasonable explanation. But still I wonder how come the Nexa remote works like a charm? Unfortunately I have already invested in such a "magnetic antenna". So no more gain to get....

I find the the combo of Nexa on/off switches and Rfxcom433 pretty unstable. In my particular case I have a Nexa WMR-1000 on/off receiver mounted behind a wall switch less then 10m away from my Rfxcom. This combo is very unstable. Some days it works pretty well, other days I can switch on the light ...

Ok, it works but it is far from a smooth procedure. Especially when you have the sensor connected to a remote Rasp. Then this change must be propagated over the remote interface as well.

I managed to replace the sensor and the history is now available. But I still have problems to find it on the ...

I have bunch of cheap Viking temp sensors attached to my system through a Rfxcom433 transciever. They have worked very well for about a year, but all of a sudden my outdoor sensor stopped reporting data. My quess was this was due to low battery, but I couldn't check this until this weekend since it ...

Ican't modify the Wiki either. I have done that before without any problem.

Something has happened quite recently!

Edit:

It seems like you must have a Mediawiki account to be able modify the Wiki. I have never logged in before, but still been able to modify the Wiki. Now I had to re-activate my ...

I have a Domoticz configuration (v3.5877) on Rasp 2 with a RFXCom433 attached(firmware version Ext/1006). It has worked fine for a while with a few temp sensors (Viking) and Nexa switches. Occasionally I miss temperature readings from one sensor due to bad coverage, but I can live with that ...