ok so I select the whole flow and give copy.
Then new FLOW and ctrl+V

Question:

Where do I put the shelly ID?

You showed me where to put the IDX switch and temp - thank you
Where do I put the shelly ID?

I'm testing this new flow for the second day and everything works fine.

Where do I provide the switch IDX and temperature IDX?

1. I just need to turn on the flows and dashticz stops working properly.

2. I start a scene in domoticz and then the lighting from the sensors stops working, i.e. communication between Domoticz and sonoff 4ch.

Did you already test with the 2 nodes, I sent you? YES: TestowyFilter.png Unfortunately it doesn't work. Communication is down. - Dashticz stops working. - Lighting from sensors also - in this case new domoticz settings turn on the switch but there is no communication to Sonoff for Sonoff to turn ...

Is it "Dashticz" that causes the loop? I do not expect that, as I can't get an idea, how that should work. I don't think that "Dashticz" interferes with MQTT. But I cannot test that either, as I do not have "Dashticz" installed. Dashticz works correctly. After recent tests I think that: If I turn ...

1. Go to "Setup" ====> "Hardware"
2. got to MQTT (your Id = 4), called MQTT Client gateway with LAN interface.
3. What is your configuration of "Prevent Loop"? Let me know.

Test as follows. 1. Activate the push button for the Shelly in Domoticz. Note what you see in the Debug node and let me kinow. 2. Do it again with your "Scene" button. Note again what you see in the "Debug" node and let me know. I don't see any differences Switch Domoticz: switch.png Scena Open i ...

I haven't tested the above option yet. But NOTE: Although I turned off two nodes as in the post, in the morning the lighting no longer worked from the sensors, after turning off the entire flow, the lighting started working and has been working until today. The roller blind is controlled from the ...

Of course, in this earlier flow without temperature this problem does not exist.

So maybe I will skip the temperature sensor but it is a bit of a shame because I wanted to monitor the shelly temperature due to the temperature problems in the earlier shelly versions.

The blinds closed from the Domoticz scene.

I start dashticz and I already have poor performance - no response to switches.

I do this:


And dashticz starts working properly.

In this system the temperature in Domoticz does not work. There is no temperature from shelly.

So here we go with test.
I changed the name - I added the word TEST.

I think that's what you meant.

Exactly as you wrote, disabling the "domoticz in" node itself in the flow with temperature restores the system to operation.
I noticed the problem in operation after domoticz performed automatic closing of all blinds. Automatic closing is performed by a scene in domoticz.

Can you try, if it happens, not to disable the whole "flow", but only the MQTT Output node, marked "Domoticz In"
(Also a button down left) and "Deploy"

Yes, now I see that you wrote it.

Of course I will check it today.

However, there is something wrong with this flow with temperature, because if I turn it on, the dashticz stops working stably - I click on the light bulb icons and they don't work. I turn off the flow with temperature. I turn on the flow without temperature and the dashticz returns to working ...

I think we need to clean up here too.

You have only 1 such an interface configured? YES Can you show me the configuration. YES Hardware: Hardware1.png Hardware2.png Hardware3.png I recommend to you, to install MQTT Explorer on your desktop or laptop, so that you can check what happens in MQTT. I have it installed on my computer but ...

- How does Domoticz control your Sonoff device. i don't see a plug-in. MQTT? MQTT Client Gateway with LAN interface. MQTT Client.png - What software is the Sonoff running. Sonoff has AFE software installed: https://afe.smartnydom.pl/pl/pliki-to-pobrania/afe-firmware#afe-firmware-t0-wlacznik- Don't ...

Managed to clean up in NodeRed: Posprzątane.png The photo shows three flows: 1. Vents recuperator - Domoticz active flow 2. Shelly PM2 GEN 3 - Domoticz without temperature - not active 3. Shelly PM2 GEN 3 - Domoticz with temperature sensor - active on. You asked what causes the lighting to stop ...

I can describe the Satel - Domoticz communication because it is a bit complicated because the Satel alarm system communicates with Domoicz via the "Satel Integra via LAN interface" plugin. In Domoticz, the movement from the sensor is seen as follows: okno-garasż.png That's why I created events in ...