Hi Pipiche, Thank you, found it and works perfectly! Channel has been changed. As for the signal power, is there any information on the current signal power of the coördinator (Using the Sonoff dongle with the CC2652P chip)? I see the setting in the Settings screen of the plugin but no option to see ...

Hello all, I have been running my new Sonoff zigbee 3.0 USB dongle plus-P since last weekend and I noticed that several devices (mainly sensors like temp/hum and smoke sensors) stop responding (or at least sending updates) after a while. Tried to pair these devices again and at that time i do get ...

Just a quick update. Removed the PiZigate and using the Sonoff USB dongle now, everything worked as mentioned above (only needed to pair al devices with the Sonoff)!

Thanks for the help!

Hi all, Been testing with a spare Pi 3B that i had laying around and installed Domoticz and plugin from scratch. Used the online installation manuals that can be found (well documented by the way!) and found that the Sonoff is working on the spare Pi. I did notice following instruction on the online ...

Hello everyone, Finally had some time today to move ahead with this and to try the suggestions. I have only one plugin configured on the pi now (on the PiZigate+) and today i removed the PiZigate+ module and added the Sonoff USB dongle +. I changed the settings in the Zigbee for Domoticz plugin to ...

Hi, Thank you for the reply! That is very interesting! So if i understand you correctly I should follow these steps: 1. Shutdown Pi and remove the PiZigate module 2. Switch on the Pi and plug in the Sonoff USB dongle 3. Reconfigure the Plugin to use the Sonoff instead of the PiZigate 4. Pair the ...

Hi DJ, I currently have a PiZigate+ V2 (internal antenna) and I am not so impressed with the stability and range of it. This is why i purchased the Sonoff 3.0 USB dongle plus. My goal is to move the devices from the Zigate to the Sonoff and then remove the Zigate (not going as smoothly as I hoped ...

Hello all, I have purchased the Sonoff 3.0 USB Dongle Plus (TI cc2652p chip) and I am trying to get it to work with my current Domoticz setup. I have a PiZigate+ v2 in my Raspberry Pi and have following versions of software: - Domoticz Version: 2023.1 (build 15182) - Zigate-plugin: version 6.3.012 ...

Got it to work already. The manual say hold the pin in the small hole on the side for 5 seconds but after 2 seconds the green led start blinking fast and that is the point that the pin needs to be released, not at 5 seconds as it seems to break of the pairing at that point. Got it paired now and see ...

no worries:) I get the following information after trying to pair the motion sensor: ----- Version: "3" ZDeviceName: "" Status: "UNKNOW" SQN: "00" Ep: Heartbeat: "4" RIA: "6" LQI: 4 Battery: Model: "" ForceAckCommands: MacCapa: "80" IEEE: "cc86ecfffea414c2" Type: ProfileID: ZDeviceID: App Version ...

Hi Pipiche,

What link are you referring to?

Thanks!

Regards,

Mark

Thnks Pipiche! I will take this up with the vendor.

Thanks for the reply:)

Hi, Is there any lead on when the Lidld/Silvercrest smart motion sensor (model SMSZ 1 B2) will be supported through my Pizigate+? I had it running on the Pizigate V1 (was recognised and working properly) but under Pizigate+ V2 (firmware 0322) and plugin version 6.3.011 it doesnt seem to get ...

Hi Pipiche, I have been resetting my Pizigate a few times last two days, i have a feeling that this is being caused by a setting that i change on the advanced setting page in the plugin. I can add devices without issues after clearing the Pizigate and starting over. However when i alter some ...

Hi all, I am registering my Zigbee devices on a new Pizigate+ v2. I tried to add my IKEA Tradfri outlet and small aquare IKEA remote to the Pizigate but i am running into some problems. My outlet and remote do not get found/registered properly, in the pugin they get registered as either a ...

Hello all, Sinds a few days i am noticing following error in my Zigate logs (and in Domoticz logs): Error: Zigate: NXP_Extended_Error_Code - Extended Error Code: [87] No free entries in the extended address table (resource error) - this table is configured in the ZPS Configuration Editor What does ...

Hi Pipiche,

Just a quick update. I installed the fan two days ago and did not have the issues since. Temperature is and stays around 58/59 degrees now instead of 80/81 degrees before.

So i guess it was the temperature!

Thanks again for your help!

Kind regards,

Mark

Thanks Pipiche. I will monitor the logs closely next few days.

I did notice the temperature being little over 80 degrees on the Raspberry, not sure if that can cause these issues but ordered a fan neverteless to get the temperature down as well.

Kind regards,

Mark

I purchased it in october 2020 so basically little over 1,5 years old i would think.

Could it be a problem with older hardware (or malfunctioning hardware)?

Thanks.

Kind regards,

Mark

Hi Pipiche, Thank you for the reply! Nothing changed in my setup last weeks, i have updated the plugin to v6.1.004 yesterday hoping to resolve the issue but it didn't unfortunately. Since this morning the issue has not occurred yet but i enabled the debug setting that you mentioned and will come ...