I'm only able to answer your first question

belgo wrote: Saturday 09 September 2017 23:04 - is there a command to know the version of running Homebridge software ?

This should work......but is doesnt! But this does works...

Day/Night time

_{[attachment=0]Daylight.zip[/attachment][attachment=1]Daylight48_On.png[/attachment][attachment=2]Daylight48_Off.png[/attachment]}

Alarm System Arming state

_{[attachment=0]SecuritySystemState.zip[/attachment][attachment=1]SecuritySystemState48_On.png[/attachment][attachment=2]SecuritySystemState48_Off.png[/attachment]}

Klik Aan Klik Uit wall plug

_{[attachment=0]KaKuWallplug.zip[/attachment][attachment=1]KaKuWallplug48_On.png[/attachment][attachment=2]KaKuWallplug48_Off.png[/attachment]}

Action

_{[attachment=0]Action.zip[/attachment][attachment=1]action48_On.png[/attachment][attachment=2]action48_Off.png[/attachment]}

Satel Integra INT-KSG Panel

_{[attachment=0]Satel-INT-KSG.zip[/attachment][attachment=1]Satel-INT-KSG48_On.png[/attachment][attachment=2]Satel-INT-KSG48_Off.png[/attachment]}

Plugwise Circle

_{[attachment=0]PlugwiseCircle.zip[/attachment][attachment=1]PlugwiseCircle48_On.png[/attachment][attachment=2]PlugwiseCircle48_Off.png[/attachment]}

Nest Heating

_{[attachment=0]NestHeating.zip[/attachment][attachment=1]NestHeating48_On.png[/attachment][attachment=2]NestHeating48_Off.png[/attachment]}

Nest Eco Switch

_{[attachment=0]NestEco.zip[/attachment][attachment=1]NestEco48_On.png[/attachment][attachment=2]NestEco48_Off.png[/attachment]}

Nest Home/Away Icons

_{[attachment=0]NestAway.zip[/attachment][attachment=1]NestAway48_On.png[/attachment][attachment=2]NestAway48_Off.png[/attachment]}

Perfect. Thank you.

A bit off-topic perhaps but I was wondering if a similar method could be used to check whether or not a specific MAC addresses are present in the ARP table of the Microtik router. This way, precense detection for eg. my mobile phones would be more reliable and less batery ...

I just wanted to make it look more familiar so I created a custon icon. This is the Winbox icon.

Thanks for the plugin. It works like a charm.
The logging is a bit much though. It would be nice to make it less chatty.

[url]http://IP_ADRES_CAMERA:PORT/cgi-bin/hi3510/snap.cgi?&-getstream&-chn=1[/url]
[url]http://IP_ADRES_CAMERA:PORT/web/cgi-bin/hi3510/param.cgi?cmd=snap&-chn=1&-continue=0&-getpic[/url]

I've tried to get this working several times now. Still without success. This time I stated with a clean and fresh Jessie Lite.

The installation end with the following error:

make: Leaving directory '/home/pi/ipcc/node_modules/unix-dgram/build'
gyp ERR! build error
gyp ERR! stack Error: `make ...

Could it be the date notation? ts\":2016-10-27 12:00:00,

If I look at the "power" part (the part that is working), the incomming payload looks like this:
{ "topic": "plugwise2py/state/power/000D6F000037B1BB", "payload": "{\"typ\":\"pwpower\",\"ts\":43990,\"mac\":\"000D6F000037B1BB\",\"power\":49 ...

I had all of this working perfectly until I reinstalled my Domoticz system. Now all is working except for the "energy" part. I have tried to figure out what is at fault but I am stuck! :oops:

This is the error I get in Node-RED:
27-10-2016 13:20:55Plugwise2 Energy to Domoticz
function : (error ...

My bad! Looking in the wrong place. Found it. Sorry for hijacking this post.

http://i.imgur.com/RMx8Tc3.png

This is how i see them in domoticz


Hi arjanvdwiel,

Would you mind sharing you smoke detector icon on the forum? (or PM) I like it and there is nothing in Domoticz like that by default.
Also, how did you get a reset button and how do you send this command to the ...

Thank you very much BADZ !
All is working again. You made a lot of PiFace users happy.