So i am not the only one with a blue Domoticz page after update to the latest version.
i luckily made an update but was not even able to restore it.
Therefore i place new RPI software and a new install of domoticz on a new SD-card
A lot later i found that the RPI imager placed the new trixie on the ...

good evening,
i think i have found it.
i am using "Monit Service Manager"
it is running for 10 hours after stopping the monitor.
next challenge is to figure out why.

regards

hello all,
i am running two RPI with domoticz but one is rebooting multiple times a day and can't figure out why.
i have found something on Domoticz troubleshooting about crashlog / signal handling.
Below a snapshot of the lines around the signal_handler.

Thread 2 (Thread 0x6d8ff200 (LWP 4287)):
#0 ...

Thanks,
but i am not skilled enough to do that,

So a few days later:
try to start mysgw but " sudo: ./bin/mysgw: command not found" is a unwanted response

during make i get the following error (and some warnings)

hal/architecture/Linux/drivers/core/interrupt.cpp:33:10: fatal error: stropts.h:
No such file or directory 33 | #include <stropts.h ...

thanks walter,
i could not find that page.
have a good year

I have currently NRF24l10 currently working on my RPI as gateway for Mysensors.
and currently busy to "rebuild" my Domoticz and upgrade it to a RPI4.
i have considered migrating to HA but it is not that appealing as i hoped.
so now i am stuck with adding the NRF24L10 to the RPI connector.
i have 3 ...

EgiGeoZone Geofencing is still available.
it would be nice to have some more guidelines how to use this in Domoticz

thanks

i just found this topic
Re: Ability to group some devices with a dedicated view.
So will dive into templates.

regards

hello,
i have tried to find this suggestion in this topic but haven't found it.
I have too many switches in the switch tab and temperature devices in the tep tab.
it is possible to copy a few to the dashboard tab but then this tab would turn into a unreadable tab. with to many entries.

So it would ...

hello all,
one way or another but Domoticz main crashes after prox 10 hours since i have been struggling with master/slave RPI.
I cannot find the reason so installed Monit for help.
But the webpage shows domoticz not connected. I have checked the setting in security trusted network and 127.0.0.1 is ...

that can be the case (see attm).
So if i make a copy by using blockly / dummy then is should work ?? (see IDX53 is a copy of IDX38)
but that's not the case,
also if e.g a tuya plugin does not work ahould i not get the selected switches (user set devices) in the main RPI in the Slave RPI ?

i have been playing around but the only thing i could find is that only everything from tab "utility" is seen at the "main" rpi

Thanks,
i did. for the last 6 years and therefor i get the gas and power from 1 RPI to the other.
But that's all i get.

Yes, but I can't figure out how it should work.
i have added one switch to the "remote" RPI so this one has a IDX. how do link this switch with IDX to a dummy switch with of course another IDX.
Or does it not work that way.

hello all,
i have two running Domoticz on two RPI.
One only to read the gas and power consumption (meter) and the other for the switches (main) etc.
But i have attached a few switches to the meter RPI domoticz.

How do i get the status of those switches to the main RPI ?

Domoticz remote server is ...

tenx
let's dive into it this weekend.
should get something to work

hello experts,
i have two Rpi's with Domoticz and want to use a switch button on the client to switch a light on the server and v.v. via MQTT
Sounds simple but can't get it work.
assume i have a situation like mentioned in "https://www.domoticz.com/wiki/MQTT#Architecture" where "other" is my second ...

that's exactly what happened to me today after installation.
the manual switch work on my domoticz. but not when a leave or enter the geofence.
the geofence button on the bottom is also not very clear to me.
if i hit the button then the line disappears from the icon but the text "all geofences are ...

Hello All,
i have spent some time searching where to get help with the Denon Wiki,
and have no idea where to post this topic,

I am using Domoticz for a long time and have added more and more overtime.

adding my Denon receiver and Heos became the next challenge,

but i get stuck during adding the ...