Aah okay. Because you're working with the Temperature sensor you have to rewrite the rule. I used the PIR Motion Sensor so that's why I used the Occupancy option.

Is there someone that resell a flashed Tasmota zigbee coordinator? [ Dutch ] I only have one Sonoff Zigbee Bridge, which I flashed myself and which I'm actively using. If you already have a Sonoff Zigbee Bridge you may send it to me so I can flash it with Tasmota and send it back to you. If you don ...

Has anyone got this working yet? I've now got my Sonoff Zigbree bridge working and paired to a few test devices and am trying to figure out how to get Domoticz to read/update them. I'm starting to look at Node-RED to see if that helps. Yes, I got it working without Node-RED or special plugin. I don ...

This is the script is currently have activated: commandArray = {} if (devicechanged['Binnendeur kleedkamer'] == "Open" or devicechanged['PIR kleedkamer'] == "On") then if (otherdevices['IsDonker'] == "On") then if (otherdevices['1 min timer kleedkamer'] == "On") then commandArray['1 min timer ...

I did activate this script, but as soon as I open my door the light goes on and immediately off again. It also switches off the 30 min timer slapen. I did write the ON/OFF commands which were being send after the rows. So you know what is happening. To me it looks like the script is turning off the ...

Thank you very much for your help so far, manually switching the light with the wall-switch is working. But I manually activated the 30 min timer slapen and triggered the PIR and door-sensor, but the light doens't go on. Please find my script below. It may is worth noticing that the script did set ...

This is awesome! I was looking for a cheap device which could alarm me in case of fire, waking up, etc. This is exactly what I was looking for. Is it possible to make the doorbell and the siren both a seperate sensor in Domoticz? So I can have a seperate doorbell switch and a seperate siren for ...

Hi all, I currently have my lights in the dressing room being switched with Blocky, but it is somehow a little limited and not really 'smart'. I hope someone can help me writing this logic in LUA. Setup: door open sensor, pir in room, manual switch in wall on 433 MHz, switched light, IsDark sensor ...

I think this one will work for sure, because it has a learning feature: https://nl.aliexpress.com/item/Smart-Home-DC-12V-220V-10A-1-Ch-Wireless-RF-Remote-Control-Receiver-Relay-Switch-315/32785263989.html?spm=2114.010208.3.150.kOoeRe&ws_ab_test=searchweb0_0,searchweb201602_2_10152_10065_10151_10068 ...

Hi guys, I saw this cheap light switch on AliExpress, it is 433 MHz so in theory is should work with my RFXtrx433E. Can anyone confirm I get this to work? https://nl.aliexpress.com/item/New-Wireless-ON-OFF-220V-Lamp-Remote-Control-Switch-Receiver-Transmitter-1-2-3-ways/32791286751.html?spm=2114 ...

You can send on hardware page or ESP-link, if it's successful you'll see "PS: 1"
If you don't see this message, there is something wrong with the communication from the ESP to the Gateway

Send the message PS=1 manually

Nobody?

If you want to be future-proof, please create CAT6 cables EVERYWHERE in your house and make a patch-panel at a central location. This way you can do whatever you want, because the cables are already there and you simply have to create some GPIO relais.

Hi all, Ik bought this wireless remote for communication with Domoticz: Hotest-Universele-ABCD-Sleutel-Controle-433-92-MHZ-Remote-Klonen-4-Kanaals-Auto-Garagedeur-Duplicator-Rolling.jpg It is working a little bit, because Domoticz sees the following sensor when I push a button: Screen Shot 2017-04 ...

I'd love to be a beta tester too!

This is especially relevant when you want to tweak your central heating system. Because HR-ketels have the best efficiency when the retour-temperature is below 45ºC.

Looks good to me!

This seems correct, you may also simplify it to have only one row for setting Bagno = On. You can create: If <<Sensore Bagno 1 = On> OR <Sensore Bagno 2 = On>> AND <<Time >Sunset> or <Time <Sunrise>> AND <Bagno = Off> Do Set Bagno = On Make sure you nest Sensore Bagno 1 & 2 in ONE block. And to nest ...

Looks good to me, but maybe you can add <Bagno = Off> to the first two rows. Because right now Blocky is constantly setting Bagno = On, where it is only needed to set Bagno = On while Bagno = Off.