Hi, The plugin works... very happy. But in Domoticz the wind is in km/h and on my display of the weatherstation it is in m/s. I've got an Eurochron EFWS2900 (similiar to the Alecto WS5500). How can I change km/h to m/s, and also how can I change the solar radiation to KLux instead of Watt/m2 Many ...

Hi If I will use this plugin, will Domoticz update my devices every 60 seconds? I understand Wunderground will only update every 10 minutes or longer, as there is a limit for downloads (500) a day. My old weatherstation (433mhz) updated every 16 seconds the devices in Domoticz. Hope someone can ...

Hi, I boughed this keychain 4 button fob from Nedis. It shows up in zigbee2mqtt as a TS0215a transmitter. When I push the four buttons, in putty-console the buttons show like 'arm.....' 'disarm' etc.. just as shown as on the zigbee2mqtt page. In Domoticz on the zigbee page, the device is shown as ...

Hi, Just boughed this bulb: https://www.ledstripkoning.nl/speciale-leds/zigbee-philips-hue-controller/hue-compatible-lampen-en-spots/zigbee-led-filament-lamp-dual-white-7w-e27-fitting-amberkleurig-hue-alternatief-led-lamp/ Tried to pair this bulb with Domoticz, using RaspberryPI with C2253sniffer ...

In the log (sudo journalctl -u zigbee2mqtt.service -f) the motion sensor TY0202 shows up like this: dec 02 18:51:12 raspberrypi npm[13388]: Zigbee2MQTT:info 2020-12-02 18:51:12: MQTT publish: topic 'zigbee2mqtt/MotionSensor_Z001', payload '{"battery_low":false,"linkquality":0,"occupancy":true ...

Hi, I boughed a EcoDim E27 G125 Zigbee bulb (www.ecodim.nl). I can pair it with zigbee2mqtt with my cc2531, but it doesn't show up in Domoticz How can I add this bulb to Domoticz? The 'problem-bulb' is the Paulmann as listed in this file (it's listed below the Ikea-bulb) Many thanks in advance Hein ...

Hi, After the Domoticz upgrade to 2020.1.. I need to have Buster installed. Now I get errors on : pi@raspberrypi:~/LGAC_SmartT $ sudo systemctl status lgac_serverW ● lgac_serverW.service - LG AC Device Server Loaded: loaded (/lib/systemd/system/lgac_serverW.service; enabled; vendor preset: enabled) ...

It's strange, because when I reboot the Pi (not my AC's) everyting is running good again... I'm going to make a fresh install again... but now installing this 'scripts' at the end of all my other devices (P1 meter, KWh-meter, GPIO-settings, Zigbee, MQTT etc...) Also making different folders for my ...

When I start (or restart) Domoticz:
After a while:

Both ac's can be controlled in Domoticz. But after a few hours or days one or both ac's can't be controlled. Got some errors in Domoticz log. After a restart both ac's can be controlled again.

Who's got the same problem.and knows how to fix this?

PROBLEMS SOLVED !!!

Installed MQTT Discovery and set SetOption 19 1 in all devices, accepted new devices...... and all devices came in automatically...
Smart Filament Lamp is now the way it should be

Many thanks to all

And on the webpage of my device in Tasmota, it shows this:

If got this settings and bulb:
I will backup my SD-card of my Raspberry Pi, after that I will try to update MQTT WITH DISCOVERY
I'll find out how to install this on my PI (Stretch-version)

Hi, I've got an E27 LSC Smart Filament Bulb (big one), I've flashed it with Tasmota, put on the right template. Everything works when I connect to my bulb on that IPadres. I can change the bulb-color and the bulb-intensity. So no problem for sofar. When I try to add the bulb to Domoticz I get stuck ...

Yeeaaahhhhhh, finally got it all to work. When you have multiple AC's and you want to control them all in Domoticz you need to make some adjustments. Copy for each AC the file LGACServerNew.py to LGACServerNew2.py (or LGACServerNew3.py and so on) In this file you should change 127.0.0.1 to 127.0.0.2 ...

Finally it works with ONE ac.. now I want to add my second ac. Anybody knows how to do that?

Many thanks in advance

WOW !!! Problem solved..... I had Raspbian Buster installed, went back to Stretch and no problems with installation....

Didn't copied the folder to domoticz yet.
I've 2 airco's and want them both installed in Domoticz, how will I do that?

After that I will copy folder to Domoticz

Finally I boughed a brand new Raspberry Pi 3B+

Installed newest Raspbian software
updated everything...

but now I get problems at the point where I logged in to LG and put the return URL in EXAMPLE.PY

see my screenshot with a lot of errors....

Hi... Finally got some problems solved... created a new LG-account, and fixed a type-mismatch in the URL. But now the following error occurs: When I get to this point: To check if the server is operating properly type: ./LGACServerNew.py. pi@raspberrypi:~/LGAC_SmartT $ ./LGACServerNew.py Traceback ...