cannot see z-wave devices

[course66]

Hi,
I installed an Aeon USB Stick Gen 5 on the raspberry pi 2, after having linked it to the Stick the Fibaro motion sensor. Domoticz firstly saw both the Aeon and Fibaro devices within the Aeon Stick setup page, but couldn't see the parameters (light, temperature and so) related to Fibaro device on devices page. After a domoticz upgrade the setup button on domoticz is red

Screen Shot 2016-03-05 at 08.35.21.png (260.53 KiB) Viewed 4128 times

and the device setup page is empty

screenshot10.png (108.06 KiB) Viewed 4128 times

I did stop and started again domoticz without solving this issue.
can anyone tell what should I do?

thanks and ciao,
gabriele

[jvdz]

Does the domoticz.log show any errors?

Jos

[course66]

nope
unless these http://www.domoticz.com/forum/viewtopic.php?f=6&t=11002 but I do not think they are related.

[jvdz]

Well your domoticz.log should at least show the startup messages and for z-wave the devices it found in the config.

Jos

[course66]

very strange, I rebooted the rpi (after system update) and now setup button in blue.

Screen Shot 2016-03-10 at 20.14.53.png (203.45 KiB) Viewed 4110 times

When I click on the setup button two pop-ups appear:

Screen Shot 2016-03-10 at 20.15.02.png (69.63 KiB) Viewed 4110 times

Screen Shot 2016-03-10 at 20.15.07.png (84.18 KiB) Viewed 4110 times

[course66]

then I see the devices in the Aeon setup page:

Screen Shot 2016-03-10 at 20.15.12.png (286.85 KiB) Viewed 4109 times

but couldn't see the Fibaro on the devices domoticz page. I see only two switches related to Aeon Stick

Screen Shot 2016-03-10 at 20.18.23.png (168.54 KiB) Viewed 4109 times

[StephaneG]

Hello,

Devices 43 and 44 are your fibaro's sensors (their ID's are 000002xxx, and 2 is the fibaro's node number).

Regards,
Stéphane

[course66]

why fibaro sensor appear as two switches when it is a there-in-one sensor (motion, temperature and light)?
what should I do (apart click on green arrow)?
I also see some strange devices related to rpi2, could be from Fibaro sensor?

Screen Shot 2016-03-10 at 23.32.51.png (166.57 KiB) Viewed 4069 times

thanks
gabriele

[Slinkos]

Maybe the wrong port was selected

[bbqkees]

why fibaro sensor appear as two switches when it is a there-in-one sensor (motion, temperature and light)?
what should I do (apart click on green arrow)?
I also see some strange devices related to rpi2, could be from Fibaro sensor?

Screen Shot 2016-03-10 at 23.32.51.png

First follow the following guide so the ZWave stick will always have the same USB port number after reboot.
http://www.domoticz.com/wiki/PersistentUSBDevices

Second remove the 'SBFSpot' hardware in your hardware list. This gives the 'wrong' devices in your list.

[course66]

thanks bbqkees,
I'm getting your suggestions. I'll try. Unfortunately now I'm out of home and mydomoticz is not working (for me).

[course66]

Hi bbqkees,
I removed Aeon, made Aeon persistent on usb, deleted SBFspot, re-booted, connected Aeon hardware to new USB port.

Screen Shot 2016-03-14 at 20.48.15.png (127.82 KiB) Viewed 3983 times

Screen Shot 2016-03-14 at 20.48.29.png (208.3 KiB) Viewed 3983 times

but...

[course66]

I still see only two switches

Screen Shot 2016-03-14 at 20.48.39.png (319.76 KiB) Viewed 3979 times

even if from the log it seems that domoticz+aeon can read other devices...

screenshot1.png (331.69 KiB) Viewed 3979 times

any idea?

thanks and ciao

[bbqkees]

Did you try to exclude and re-include the device?

[Kroontje]

Disable polling for the motion sensor, wake up the sensor by 3x clicking the include button and filter under Devices for Aeon or '00002' and see what shows up. The logging tells you that the Temperature and Luminance nodes are added.

[quique]

Hi,
Any news on this? Did you find a solution to the problem?

I have the same situation, installed a z-wave sensor (Secure) with 2 probes for tubes temperature measurements, so a total of 3 measurements in the same sensor and even if at the device registration shows in the log the fact that the sensor has different temperature registers I can see only one device in the setup/device menu and indeed receive only measurements for that device.

I can see the channels in the control panel but not as devices in domoticz.

Screen Shot 2018-01-12 at 09.17.21.png (76.05 KiB) Viewed 2570 times

My setup is domoticz with Synology NAS and the USB z-wave key.


Thanks for your help.