domoticz in synology as package! Available now.

[Smiggel]

I installed version 3.0.5877-7 through the package manager. I added http://www.jadahl.com/domoticz_stable/ to my package sources and installed Domoticz on my DS214+ using DSM Beta 6.2. However, the package fails to start. Tried a reboot of my NAS, but still did not help.

Does anyone have a solution for me on how I can get the package to start? Really want to try out Domoticz.

[Gravityz]

well you probably installed the wrong package.

you say you have a DS214+ with DSM beta 6.2 but you show the link which is the stable 5.2 version.

i think you need to uninstall everything(do areboot to make sure evrything starts up normal)

then just go to this page , download the armadaxp version and install that one
i think the 6.1 version will also run on the 6.2 beta dsm version

http://www.jadahl.com/domoticz_beta_6.1/

maybee Jumbotroll can compile the armadaxp 6.2 version for you.

you could also add this link to the packet manager to get the same result
http://www.jadahl.com/domoticz_stable_6.1/

again i think 6.1 will run on 6.2 beta but not 100%sure

[Smiggel]

Whoops, I see the link is wrong indeed. Installed the 6.1 version manually and that works.

Now I can figure out how Domoticz works.

Thanks!

[jumbotroll]

again i think 6.1 will run on 6.2 beta but not 100%sure

I can confirm that DSM 6.1 version should work on DS214+ (armadaxp) because the toolchain and kernel is the same for armadaxp in DSM 6.2 Beta.

[Smiggel]

Yep, thanks again! It’s running.

[Gravityz]

glad i could help.
You will find that Domoticz is not 100 perfect but you can customize a lot to make it 100% perfect with scripting.

[teo1966]

hello i have a problem 1 veld is red ( AANVOER-TEGEL )how is this possible

[Gravityz]

it turns read when it is not seen for a while.

if you turn polling for this device on it will probably be solved
without polling the device needs to report the status either on a regular base(reporting) or on a change base.(if temp changes by a certain degree.)
if the reporting is turned of and you have a temp delta set for lets say 0.5 degrees and that temp never changes with a max of .5 degrees then nothing gets send to domoticz.

ofcourse there could be something wrong with the module itself
what module is this?

[teo1966]

this is Universele Binaire Sensor FIBARO FIBARO Temperatuur whit 4x Sensor ds18b20 Waterproof and Z-wave Plus USB Controller Batterij Z-stick AeonLabs

[Gravityz]

check parameter 11 and 12

11 is about forcing to send a report(must be non 0)
12 is about the delta temperature (the change in temperature when a report is send(set to 1 or 2)

this is Universele Binaire Sensor FIBARO FIBARO Temperatuur whit 4x Sensor ds18b20 Waterproof and Z-wave Plus USB Controller Batterij Z-stick AeonLabs

[gijsje]

Can the latest beta be made with python?
Thanks in advance

[jumbotroll]

Can the latest beta be made with python?
Thanks in advance

For DSM 6.1 ?

[gijsje]

yes please

[jumbotroll]

yes please

It take a couple of hour to compile all versions, what version do you want and I can build that version first...

[gijsje]

it is for the DS218+ so i think it is the Appololake?

[jumbotroll]

it is for the DS218+ so i think it is the Appololake?

Yes it's Apollolake.
Check here in 20 min..
http://www.jadahl.com/domoticz_beta_6.1_python/

[gijsje]

Thanks very much

[gijsje]

made a small donation for some beers
Thanks for all the work

[jumbotroll]

made a small donation for some beers
Thanks for all the work

Thanks
Apollolake is updated.

[mcwieger]

After updating DSM to 6.1.5-15254 Update 1, Domoticz has become unresponsive. I can open Domoticz, when pressing buttons they respond, but the actual devices don't switch on or off. Anyone else experiencing this? I have a DS414 (ArmadaXP).