Cheap 433MHz door sensor (with open and close)

[JelteV]

Hi,

So I don't know if this is special or not but I found these cheap Door sensor that look great, are really cheap (<€ 5,-) and send an open and close signal.
https://www.aliexpress.com/item/433MHz- ... 91010.html

IMG_4198.JPG (32.29 KiB) Viewed 18686 times

I thought I would share how to set them up in Domoticz.

So first this sensor has to be picked up by Domoticz. If you have an RFXCOM you need to enable the Lightning 4 mode.
As soon as this is enabled your sensor will show up in your list of (unused) devices as 2 devices with the same ID.
One device will be triggered when the door is opened, one will be triggered when the door is closed.

You need to find out which device is triggered when. You can find out by triggering each event. First move the contact away from the base, this will simulate opening the door. The "last seen" time of that device will change.
Rename that device. Let's call it "Front door open (event)".
Now move the contact back to the base. If you did it correct "last seen" time of the other device will change.
Rename that device. Let's call that "Front door close (event)".

And add them both as switches in Domoticz.
Both devices will be always on, you can't switch them off. To know the state of the door we need to add a new dummy switch.
Add a new dummy door contact and call it "Front door (Virtual)".

To know the state of the door we need to add 2 small scripts.
One when the door is opened and one when closed.
Here they are:

Spoiler: show

Door open :

Code: Select all

return {
	active = true, -- set to false to disable this script
	on = {
		devices = {
			'Front door open (event)',
		},
	},
	-- in case of a timer event or security event, device == nil
	execute = function(domoticz, device)
		if (device.changed) then
			domoticz.devices('Front door (Virtual)').open()
		end
	end
}

Door close :

Code: Select all

return {
	active = true, -- set to false to disable this script
	on = {
		devices = {
			'Front door close (event)' 
		},
	},
       -- in case of a timer event or security event, device == nil
	execute = function(domoticz, device)
		if (device.changed) then
			domoticz.devices('Front door (Virtual)').close()
		end
	end
}

There you have it.
A working 433MHz door contact in Domoticz with an open and close for less then € 5,-!
Now you always know the state of your door or window.

[aleph0]

Thanks you very much for this info I've been looking for something like that for a long time

[Rolo]

Can you tell wich type of battery is used in this switch?

[sincze]

Nice find. Even open/close. Well design looks also okay. Next stop will be their motion sensors right??

[SweetPants]

Can you tell wich type of battery is used in this switch?

If you follow the link in the first post it says:
Power Supply:DC 12V(12V 23A battery)

[Jem101]

Can you tell wich type of battery is used in this switch?

If you follow the link in the first post it says:
Power Supply:DC 12V(12V 23A battery)

Yes it does say that but it must be a misprint somewhere - a battery that can supply 23A at 12 V is a car battery! I suspect, looking at the other similar products, that it'll be something like a CR2032 button-type cell.

[SweetPants]

23 A is the battery type http://www.toolstation.nl/shop/p92000?c ... gIvJ_D_BwE
very common type is chinese sensors. They are a little expensive in use

[Jem101]

23 A is the battery type http://www.toolstation.nl/shop/p92000?c ... gIvJ_D_BwE
very common type is chinese sensors. They are a little expensive in use

Ah I didn't know that - I stand corrected!

[DzJan]

Confirmed, the mentioned solution here is the best one found sofar.
A method using master/slave does do the open/close toggle but it is not logging the state in the switch' log.

Tips:

• When successful implemented, set the devices "Front door open (event)" and "Front door close (event)" as hidden via Setup -> More options -> Plans -> Roomplan. Select the line $Hidden Devices and Add the two devices.

• I used an similar sensor type, that actually uses an AAA 1.5v battery https://nl.aliexpress.com/item/5pcs-433 ... 0.0.rBYZOF

[BartSr]

Maybe this might be helpfull.
I found this instruction which clearly explains how to.
https://www.youtube.com/watch?v=Oq-hN-RJ2sA

[Milifax]

Maybe this might be helpfull.
I found this instruction which clearly explains how to.
https://www.youtube.com/watch?v=Oq-hN-RJ2sA

My advice: don't use the master/slave option. It will save you a lot of trouble if you skip that part. Just add then as on or off devices.

See my struggle in a previous post:
viewtopic.php?f=59&t=18654

[BartSr]

@Milifax: Thanks for pointing me to the unwanted side effect.
I just started with Domoticz and have (not yet) experience with the scripts which drove you crazy using this solution.
-Bart

[BartSr]

In addition: Is it normal that it takes (variable) 2 - 5 seconds before a change of the status is reflected in the GUI?

[MarnixO]

Hi all
i have received the door sensors yesterday
With 1.5 volt battery included
they are recognized like a X10 security sensor by rfxcom
it has 3 states Alarm, Motion and Normal
the state normal can be trigered by the dashboard but not by actuating the sensor itself
so i wrote a dzvents script to change the state of the dummy doorsensor

json output:

{
ActTime: 1509176885,
ServerTime: "2017-10-28 09:48:05",
Sunrise: "08:31",
Sunset: "18:25",
result: [
{
AddjMulti: 1,
AddjMulti2: 1,
AddjValue: 0,
AddjValue2: 0,
BatteryLevel: 0,
CustomImage: 0,
Data: "Motion",
Description: "",
Favorite: 0,
HardwareID: 3,
HardwareName: "RFX",
HardwareType: "RFXCOM - RFXtrx433 USB 433.92MHz Transceiver",
HardwareTypeVal: 1,
HaveDimmer: false,
HaveGroupCmd: false,
HaveTimeout: false,
ID: "618000",
LastUpdate: "2017-10-28 09:29:07",
MaxDimLevel: 0,
Name: "deursensor 103",
Notifications: "false",
PlanID: "1",
PlanIDs: [
1
],
Protected: false,
ShowNotifications: true,
SignalLevel: 7,
Status: "Motion",
StrParam1: "",
StrParam2: "",
SubType: "X10 security",
SwitchType: "Security",
SwitchTypeVal: 0,
Timers: "false",
Type: "Security",
TypeImg: "security",
Unit: 0,
Used: 1,
XOffset: "0",
YOffset: "0",
idx: "103"
}
],
status: "OK",
title: "Devices"
}

Is there also an other way ?

[miremi]

If i follow link from the first post item is not available anymore.

[BartSr]

Similar (or maybe slightly differrent) type are availbale on other chinese web-shops.
e.g. https://www.banggood.com/GS-WDS07-Wirel ... mds=search

[miremi]

Similar (or maybe slightly differrent) type are availbale on other chinese web-shops.
e.g. https://www.banggood.com/GS-WDS07-Wirel ... mds=search

Thank you

[Jordy]

These sensor are giving my quite a headache. Trying to figure them out via lua scripts. But as said, the status of the sensor stays ON. I'm not quite sure why it's like this.

I've followed the video linked above and once added, the dashboard shows the status correctly (Open or Closed, configured as Door Contact). But if you check the logs, it's always ON. I guess internally it's keeping the correct value. I just wonder why I can't get that internal value. It seems a bit vague to use a virtual sensor just to track the open & close status of the sensor.

The ones I ordered are: https://aliexpress.com/item/5pcs-lot-43 ... 22065.html

I guess I'll also implement a virtual sensor just to track the state.

[JelteV]

You have to create a virtual doorsensor. For some reason they are always on..
Just follow the steps in the fp.

[bassie127]

Hi,

...
To know the state of the door we need to add 2 small scripts.
One when the door is opened and one when closed.
Here they are:

Spoiler: show

Door open :

Code: Select all

return {
	active = true, -- set to false to disable this script
	on = {
		devices = {
			'Front door open (event)',
		},
	},
	-- in case of a timer event or security event, device == nil
	execute = function(domoticz, device)
		if (device.changed) then
			domoticz.devices('Front door (Virtual)').open()
		end
	end
}

Door close :

Code: Select all

return {
	active = true, -- set to false to disable this script
	on = {
		devices = {
			'Front door close (event)' 
		},
	},
       -- in case of a timer event or security event, device == nil
	execute = function(domoticz, device)
		if (device.changed) then
			domoticz.devices('Front door (Virtual)').close()
		end
	end
}

There you have it.
A working 433MHz door contact in Domoticz with an open and close for less then € 5,-!
Now you always know the state of your door or window.

Sorry, but can you tell me where and how to add these scripts?
I tried to place them in the /opt/domoticz/script/lua directory, but then I got the error 'No commandArray returned'.