I can't believe that this basic and essential function (concat 2 simple texts) is not possible in blocky in Domoticz ! IT's possible in blocky but not in Domoticz's blocky. What a pity. Thank you. I appreciate your comment. That's exactly the feeling I had when I read the answer.... But did you ...

There is a topic full off blockly examples.
Read that first before you try things...
And before you have lots of comments...

Please stop changing the widgets!! (after putting the 2x1 back) I have four pages of widgets on my Phone. Mostly using the 2x1 size. But this one seemes to dissapear en then come back and now its gone again. It is very nice working with the widgets but is it possible to update the widgets insted of ...

You have to use the type:Air Quality and subtype:Voltcraft CO-20 I have two of them, one with display and one without display. They are working perfect with nice graphs in domoticz. And when the levels get to high (>1800) I get a push notification on my android (NMA) and my RGBW leds turn orange for ...

I'm still having problems with the graphs from the Gas and CO2 meters (they won't show). For Electricity and Temp they are working OK! In the Domotictz (website) they are all working fine... This was already mentioned by me but everybody was so busy with all the new (and great!) functionalities I ...

I'm still having problems with the graphs from the Gas and CO2 meters (they won't show). For Electricity and Temp they are working OK! In the Domotictz (website) they are all working fine... This was already mentioned by me but everybody was so busy with all the new (and great!) functionalities I ...

I'm still having problems with the graphs from the Gas and CO2 meters (they won't show). For Electricity and Temp they are working OK! In the Domotictz (website) they are all working fine... This was already mentioned by me but everybody was so busy with all the new (and great!) functionalities I ...

Look here:
viewtopic.php?f=8&t=4698
And you will find lots of examples..

I tried it and it is working great!!!
Thnx!!

But I stil have problems with the graphs from the Gas and CO2 meters (they won't show).
For Electricity and Temp they are working OK!

I think stroom actual here is 3909...
But put it in a uservariabele and write it to log. And then you know for sure.

viewtopic.php?f=12&t=9344&p=65003&hilit=transfer#p65003

Don't you guys have a search button on this forum?

Barry is this working for you?

Look at your Blockly.....

You have to use the right logic blocks in the right place...

Okay... Could you send me some topics then? I've searched almost the hole forum, but i couldn't find anything to 'scrape' a value from a sensor to a dummy! Thanks! In Blockly you can choose Devices Utility and there is Gas actual and Electricity actual. Now you can make a user variabele like "gas ...

And still, you don't know if your alarm system is gone work with this solution...

Egregius wrote:No, but you do when you enable developer mode in your browser.
That way you also see the complete command that is sent. Lot's more than just one value.

Oooh Thnx!!!

I didn't know that. But it is really very handy!!
I'm not so familiar with all this web-stuff..

Egregius wrote:If you click the device you should see it's settings below the table.

But do you also see the different idx's to use for the JSON commands.... I don't
And in the devicetable you don't see the RGBW controller itself (with idx=14 in my case)

Thnx gizmocuz!! it's working!! I looked in the table ZWaveNodes and saw the following data for the Fibaro RGBW: ID=1, HardwareID=14, HomeID=25487939, NodeID=4 If you want to see the configpage of the device you must use the HardwareID: http://[ipadres]:[portnumber]/json.htm?type=openzwavenodes&idx ...

Go to devices and look for it in the list, the idx is on the left. I'm working a lot with domoticz and I know how to work with JSON en idx...... But the RGBW controller isn't a device in the devicelist, because it's a zwave node. So again my question: wich idx to use for changing the parameters of ...

I wanted to try the following command for my Fibaro RGBW device: http://localhost:8080/json.htm?type=command&param=applyzwavenodeconfig&idx=10&valuelist=72_Nw%3D%3D To use the animation program Storm on this device. But I don't know which number to use for the idx? Is it derivable from the node ...