Before I come to my next question, I would like to put the basic problem into a vision of a train journey. Basically, I want to know whether I'm on the right train at all. The journey is clear: my ZWave installation should still work even after OZW has been switched off. To ensure that the journey ...

I am preparing the migration from OpenZwave to Z-Wave JS UI and am using the tutorial from 09 June 2023 as a basis. @d3smo - many thanks for this. Is it still up to date or are there any updates? I have an installation with about 50 nodes. But I will only start the adventure with a test environment ...

The setting in the menu was the crucial clue. I think I had used that entry myself a few years ago and had been forgotten.
Thank you very much.

Hi, thank you for the reply. I am aware that the time span can be expanded. However, the details get lost and only daily values get visualized. I want to observe events with a periodicity of "some minutes" and "hours". This can be achieved with the short term (5 minutes values) setting. In Version ...

Hi, For monitoring the temperature of the heating system, I use Domoticz's very powerfull display of temperature and humidity curves. Unfortunately, as of version 2023.x, the temporal representation seems to be limited. Cache clearing didn't help either, if that will be one of the first helping ...

The problem seems to be solved. It was due to the power supply. The micro USB plug had a bad contact. However, this was not immediately noticeable because the connected Uninterruptible Power Supply (UPS) probably compensated for this to some extent. At the end that cost quite some time and nerves ...

Hello willemd - thank you for the assistance. With try and error (by using a 2nd Rasp, 2nd Zwave Stick and older backups) it turns out that polling is not the issue . This seems to be a coincidence. I assume that Domoticz is running permanently well. In some cases the web interface works fine, but ...

Here further status info: pi@Rasp3:~ $ sudo service domoticz status ● domoticz.service - LSB: Home Automation System Loaded: loaded (/etc/init.d/domoticz.sh; generated) Active: active (exited) since Sat 2022-09-17 18:04:25 CEST; 2h 56min ago Docs: man:systemd-sysv-generator(8) Process: 614 ExecStart= ...

Thank you for the analysis. This gives me a new view. Here is the result to your proposed command line: pi@Rasp3:~ $ ps -eaf | grep domoticz pi 1670 1345 0 20:25 pts/0 00:00:00 grep --color=auto domoticz pi@Rasp3:~ $ sudo service domoticz start pi@Rasp3:~ $ What can you infer from this?

After finishing the backups I come back to advice from willemd to check whether Domoticz is running with the Zwave Stick (without Stick web interface is reachable and domoticz is running!): pi@Rasp3:~ $ ps -eaf | grep domoticz pi 1563 985 0 17:38 pts/0 00:00:00 grep --color=auto domoticz How to ...

Thank you for the fast reply. First, I restartet the raspberry without the USB-ZWave stick and domoticz was reachable via web interface. This is an indication, that the ZWave stick and its inteaction with the Zwave network seems to be the reason of the problem. Than, as domoticz is available (check ...

Hello, The starting point of the total failure was the insufficient installation of Fibaro FGBS222, where none of the connected DS18B20 temperature sensors were registered in the device table. Changes of the configurations do not seem to be taken over by the device. To solve the problem I have ...

Hi awierda,

Good to know, that I am still not alone with the problem of configuring the RGBW module .
Actually, I am still waiting for somebody who can report about successfully installation - and how!

Any news?

Perfect, thank you! I knew I was only a click away...

How to import & export? Via clipboard? It does not work as the clipboard remains empty and a "blocking" sign pops up.

Find below corresponding screen shots

Hi all, Thanks for the groundwork. I had the same problem with the configuration. To activate the 4 inputs I used the value -65534 + 34952 = -30582, which was also accepted by the device. So far OK. Fibaro_RGBW_1.jpg Fibaro_RGBW_2.jpg Unfortunately I don't see the 4 expected 0-10V sensors in the ...

Perfect, now it works well. Thank you!

However, there was another syntax challenge responsible for some other strange observations on my side:
10 seconds = [10:00], not [00:10].

What is the background to set the type of event to "Device"? In which cases the other types are appropriate?

This is my first step learning more about blockly and I started with this simple example:
R02 turned on correctly when P02 was switched on, but R02 did not switched of after 1 minute. Exchanging both switches does not work ether. What went wrong?