Hi all,

I've bought a galaxy watch 5 pro, and installed a domoticz app from the play store. I could choose between the normal and premium.
I own the premium on my phone also.
I tried both, but the apps hangs on loading, blue background with domoticz D logo.
Is this a know issue?

Hi all, Today there was some powerloss. After that everthing was fine but the domoticz rasperry not. I rebooted it by power off / on, domoticz shows up for some seconds but thats all. I couldnt login from terminal. I found out some intresting things, https://howtoraspberrypi.com/recover-password ...

Zigbee newbie here too.
I got myself a new philips hue bridge but still not using it.
But today I getting a new kitchen with some led lights. Is zigbee, with a remote. Can I pair these with a hue bridge, and the hue in domoticz?

tnx.

Note that the mah in chinese shops are mostly very incorrect

Hi, I had the same issue. After buying, a half year later battery empty. That was a chinese one. I bought a duracell, it lasts for one month. I thougt it could be an old one or something, buyed in another store a new one, same issue. After three duracell batteries I bought 12 https://nl.aliexpress ...

Hello there, I have build a Xpenology Nas based on model 3615XS with DSM 6.2 RAID5 setup with 3 1TB disks, and total 6gb ram modules (2+2+1+1 gb modules) I have used the script from the wiki, blurred here my ipadress settings etc #!/bin/bash # Settings NASIP="" # NAS IP Address PASSWORD="" # SNMP ...

It is just the one or the other.

Verstuurd vanaf mijn TA-1012 met Tapatalk

I have several devices on the system alive checker, to turn a switch on or off. But there is no clear manual for this. I would like to know how I have to set a device, who's network connection is going quick off, to stay "longer on" so the virtual switch is not so quick off. Do I have to increase ...

I installed a rpi cam on board of the raspberry, and then installed motion, the description on the wiki is a little different, but OK I have installed it and added a dummy motion switch. It did not work right out of the box, but I found I had to do this: to load the model after each reboot, use this ...

Hmm. How can I send more than one on signal or off signal per switch? Verstuurd vanaf mijn XT1562 met Tapatalk In normal Lua... commandArray['MyDeviceName']=On REPEAT 3 INTERVAL 3' repeat means how many times to repeat the signal. Interval means the time between each signal command. Can I use it ...

Hmm. How can I send more than one on signal or off signal per switch?

Verstuurd vanaf mijn XT1562 met Tapatalk

did nothing special, now it aint working again...

It's a led bulb. But still then the remote should do the same thing as the rfxcom right? Tried another bulb halogene and it was about the same behaviour, suddenly the thing started to react normal again. Switched to led bulb and it's working till now. Strange, I am not fully convinced if it's ...

I have 2 temp sensors, and took the batterys off but no difference. Resettet the kaku and added on another channel of the remote, also no luck. My router is the range of 1,5 metres, powered off no difference. My microwave is on the other side of the wall of the switch about 20cm higher, cant take ...

Hello, I have a kaku light switch which is working fine with a kaku remote, but less with domoticz. I don't know exactly why. The kaku is near the rfxcom about 1,5 meters, could that be the problem? When doing on command in domoticz, it goes on, when clicking off, it wont go off. Sometimes it does ...

HFman wrote:With ESP easy 1.47, i don't need to reset.
Which software you use on your ESP ?

I've got esp-link 2.1.7 . It has an terminal interface etc.
I can use it with domoticZ.

Verstuurd vanaf mijn XT1562 met Tapatalk

I only get good results when I do the following:

Powerup the otgw and esp, wait about 2 minutes to be sure everything booted. Then use the reset button on the otgw, wait, and after that the esp is getting good data.

Verstuurd vanaf mijn XT1562 met Tapatalk

does not work. Only test image works.

well @ my setup it just wont work. With or without slash, with or without image url, only the test image succeeds. the streaming url should be http://ipadress:8081 The embedd url should be http://ipadress/picture/1/frame/ well tell me what I should fill in domoticz, I tried everything, also with or ...

I think this should it be then.
Am I correct that I not have to use time switch (tijdschakelaar-1) = off, because he only has to do something when de time switch is on?