Thanks for sharing your docker-compose.

I have not seen before the. Volume xxx .ssh and the logging lines.

Could you explain the function of these lines and how to use them in, I assume, in the browser?

Thx

Thank you both for joining this discussion. However, the discussion becomes confusing when comments are somewhat cryptic, such as "/ is correct..." and "Edit: In a normal Linux environment, init always runs. With init: true, tini is started, which is a small init" and "I will never go to dzvents ...

I installed domoticz in a Docker container and placed the data in a volume called domoticz_data to prevent data loss during a subsequent pull. The SolarEdge Modbus Python plugin is now installed in the data volume path root@44929adebcd4:/opt/domoticz/userdata/plugins#. However, the plugin ...

Sorry, but your suggestion is not very clear to.

Could you be a more specific? Somewhere a step by step guide?
Thanks

found a solution:

in the old zwavejsui configuration i made a backup of the "store".
after a docker stop for zwavejsui i copied the old configuration in the "store" location of the zwavejsui in docker. Adjusted the ip and homeassistant-prefix in zwavejsui-settings

In domoticz (container) i ...

Backups seems not to be compatible: In the past I made a zwavejsui backup from the old configuration but you cannot restore that one in the new zwavejsui in docker

default port is 8091. that works because the nodes 10, 13, 20,21,22,,26 are visible in domoticz and mqtt explorer.

you suggest a re-adding: i do not dare to do that. Why? the old configuration is still up and running. If i replace the usb controller again in the old configuration everything works ...

Hi,

I do not know how to create a "config topic"

Node 48 is a quibino flush on/of thermostatic switch. in the old configuration it looked like this:

changed zwavejsui Homne Assitant discovery prefix to homeassistant and
changed the domticz MQTT AD prefix in homeassitant.

Unplugged en plugged the power of node 48 (kickspace); No results

I tampered the motion switches (nodes 20,21,22,26). They are visible now in domoticz

Nodes 48 en 49: i unplugged the power en plugged in again. No changes (zwavejsui status for alle node completed,but no sensors in domoticz (see printscreen MQTT-explorer.)

Any expert that can help?

network gragp missing

Thanks for the link to the wiki. It works, but unfortunately only partially.
The original configuration was a PI with Domoticz, OpenZwave converted to Zwavejsui (the controller is an Aeon Zwave USB stick), and RFxCom. The Zwave USB controller managed 8 nodes. Everything worked fine (see screenshots ...

I use the MQTT autodiscovery and yes
I also use everywhere the full ip adres of the RPI and port 1883.

The same prefix in zwavejsui and in domoticz (zwave).

I read somewhere it is not possible that domoticz en zwavejsui in container could communicatiedienst which each other ( ofcourse mosquitto is ...

Hi,
normally i had domoticz, zwavejsui and mosquitto running on a raspberrypi. Due to trouble upgrading to version 2025.2 I made docker containers for Zwave-js-ui, mosquitto and domoticz.
For the Domoticz hardware setup MQTT Client Gateway with Lan interface i took the configuratie from the old Pi ...

Gizmocuz,

That's easier said than done for the inexperienced UNIX-user.
The recommended manual immediately causes problems because the example command outputs are different then mine, and you're unsure whether it's correct or not, and whether you can continue.
Docker is also recommended. I have a ...

I was browsing through this topic and it made my head spin.

What a hassle and set of steps to run version 2025-2 under Bookworm later on.

Maybe a really stupid question, but isn't it possible to use the RPI Imager to put a new OS-bookworm version on a sd-card, then run the Domoticz setup procedure ...

yes, i did

cd domoticz
sudo service domoticz stop
Test if domoticz can be started by hand:
./domoticz
but starting domoticz by hand genereated a lot of error-lines not knowing how to solve.








pi@raspberrypi:~ $ cd domoticz
pi@raspberrypi:~/domoticz $ ./domoticz
2024-10-20 16:01:05.968 ...

Hi,

i looked for the domoticz.log file, but i could not find it in the /var/log location.

What is the problem:
I have several computers and all except one are able to remotely log in into domoticz. One computer give the login-error "name and/or password" are not correct, but they are correct ...

As you advised “check the actions mentioned “ https://www.domoticz.com/wiki/Zwave-JS-UI#Configure_Zwave-JS-UI_for_Domoticz“.
In section “Home assistant” the switches MQTT-discovery and Retained discovery were not activated. Why not?
As you probably know, there is also a home automation system called ...

Succes comes at the end

Its working.

thanks a lot

Paul