Hi, thanks for the reply. menawhile i developed some ruby scripts which i run as cronjob every 5 minutes. I share the code here all comments are german- but it is very simple and therfore self explaining. the point ist that the domoticz db is getting updated every 5 mins. so i have no flapping in ...

Hi Community, right now i am testing to install an heater control for the whole house. While i am doing some evaluation - dry run. I had the following effect when steering the valves of the Wallheaters. In the first version i implemented an logic like - if temp goes below point then valve on - to ...

Hi,
i use:
Version: 4.9700
Build Hash: a3a45906
Compile Date: 2018-06-23 16:24:51
dzVents Version: 2.4.6
Python Version: 3.5.3 (default, Sep 27 2018, 17:25:39) [GCC 6.3.0 20170516]

ok,
i´ve found the Solution.
As the api sends base64 encoded string this must be decoded in dashticz.

viewtopic.php?f=67&t=17427&start=380

Hi Ierlandfan,
i was searching for the named fiel in the dashticz folder and couldn´t find the line to change.
Were is the file located? and where should be normally the line be?

thank You
br
jens

Hi Community, as i am now trust in Domoticz as a perfect System for Home Automation :-) There is a new Project which i want ti implement in two steps. The Heating Control of my inWall Heater (like floorheating just vertical) The initial installation was an wall thermostat (vry simple) you just set ...

Hi, here is an update to my levelmeter.
since installation it delivers all the time an Calue for the distance of the saltlevel. For any reason the reboot suddenly disapperar! the device works really fine.

Thanks for supporting and ideas

Hi, i used the older espeasy release. The v2.0 doens´t worked but maybe now there is a newer version out. the measuring i do is a saltlevel -> means there are salttablett in a jar which getting more and more into the water on the ground. The measurement worked in tests on all levels. Unfortunately ...

Hi, here is an update.
today the esp had an total outage with no feasible reason. So i relodad the espeasy firmware and configured and since now it wokrs with no reboot and very stable. We will see

hi, tested over the weekend and it is not stable.
The ModeMCU is rebooting every couple Minutes for any reason. I will try it with the level shifer but which one to buy?


br
jens

Hi Heggink, yes it works like a charm i used the pin with 5v on the left lower corner :-) it´s maybe because it is an Mode MCU Board Today i put it in electric distribution box with hot glue. And since now 5 Minutes it sends me the measurement :-) Only not so well is that the wlan signal is very ...

Hi All, now that all parts are bought :-) -an usb power adaptor -a mode mcu esp8266 -hc-sr04 sensor i just wired all and used espeasy to flash espeasy firmware :-) it works great :-) Created an Dummy device in Domoticz with an Leveldevice in the espeasy webinterface you just put in the domoticz ...

Hi, thats cool. meanwhile i came to the same conclusion
i will try to build it with an hc-sr04

It will be a bit programming but at the end i t will be very cool

Thank You all
Jens

Hi, thanks for the repiles :-) I think the esp8266 is what i need. I took a short look on this but actual i dont understand how i can get the measurement or the i/o status into domoticz. I would mention somethin like an url to the api. If e.g. gpio 2 = on to have an event like set domoticz switch n ...

Hi Community, i´ll do a short introduction for my problem. in the cellar we an watersoftener which has an reservoir for salt. So last i totally forgot about this and the salt was empty over long period. And i thought how could i meter the level of the salt? There is also water in the reservoir but ...

Hi,
i would also be very happy if anybody may share the code for this

Thank You
br
Jens

Hi Anybody,
are there any news about the CallMonitor. I had also the idea to have an event triggered when a call is incoming. Unfortunately i can not find any documentation about this Domoticz module/plugin.


thx
jens

Hi jimieglise, i installed your script and it is running as a service. All is fine Thanks for the Great Work. But there is one thing which makes me crazy. Example: i sit nearby the Bluetooth dongle location (with the beacon laying down on the desk) the Presence should be ok but on each checking of ...