Thanks

Thinking about it, it does tend to be the Aqara/Xiaomi devices.

Seems Sonoff is the way to go!

What are some sensible values to put in transmit power? (Currently 0)

Will avoid all things xiaomi / Aqara in future

Interestingly a Aqara/Xiaomi mains wall switch stopped working at the same ...

My Zigbee motion detectors suddenly stop working after several weeks.
This time two stopped working at the same time; they are in close range to other Zigbee devices but geographically close to eachother. It has happened over time to all my motion sensor and door sensors. (Is it related to being ...

% control now works great.

Pressing open/close when it is in operation still causes it to stop. However, I guess I can fudge that by only ever sending setLevel commands

Thanks very much.

p.s. how do I get back to the beta branch (assuming you will be integrating the changes).

Let me know if you ...

Thanks for looking at this. Just done that.

Here is the log output since the restart including a open/close/set to % event

2022-05-22 10:35:59,758 INFO : [ MainThread] onDisconnect - Closing Name: 'Zigate Server Connection', Transport: 'TCP/IP', Protocol: 'HTTP', Address: '', Port: '9440', Baud ...

Just updated to 6.2.052 with no difference

Here is the log with the debugs enabled.

Last few requests were close, open and set to 47%

Just remembered that when I was previously trying to use the blind, the % status was reported in the Domoticz log repeatedly when the blind was in motion (e.g ...

Thanks for looking

The blind is directly paired with the controller (Sonoff USB stick). The buttons in Domoticz for open/close work perfectly without fail. Using the % slider does nothing.

I haven't tried using the included remote yet (no need to in my setup)

Here is the Plugin Devices RAW

41 ...

I had trouble linking my Ikea blinds when I was using Zigate (could get it to go one way but not the toher... gave up for a while)
Just tried again now I have upgraded to a Sonoff USB stick and Zigbeefordomoticz

The blind with open/close perfecly.
However, it will not work if set at a % e.g. opened ...

Only just got to try this again..... and it connected first time!
Maybe it was because the light has been off that time and it was an issue with the device itself!

I have just upgraded from a Zigate V1 (which suddenly died) to a Sonoff USB dongle.

With the magic of ZigbeeFor Domoticz plugin it just all 'worked' with minimal hassle of repairing devices.

I noticed that I had to 'prepare device for a full reset' (in pugin interface) for a number of devices to ...

I can't download form the link either - page never loads

https://synnas.publicvm.com:4430/s/Czn9r8G8QwrZ7ji

Thanks.

Re-pairing not reay an issue

However, will wiping delete all zigbee switchee/devices from domotIcz? Or will they repair with same name/idx?

Should I get a V2 whilst at it if I can get one to the UK?


Just tried this device again (forgot all about it) after I have moved to the optiODM ...

Noticing quite a delay between pressing a button on the TS004F and the resulting actions.
Seems less with a 'double click'

Is the amount of time to decide a single click vs double click set in Zigate plugin or in the device itself.

Only other factor is that it is installed in a remote room at the ...

Just a quick update to say the TS004F is now fixed.

I am using the Zigate plugin 6.0.007 and Zigate firmware 0321.

I think it was the updated Zigate plugin that did the trick.

Just worked straight off without needing to hold down the right two buttons to change the 'mode' or any other complicated ...

Updated the github repository with 6.x one and it works fine.

I have Zigate USB v.1 device and I'm using old Firmware: 031d . In Zigate-Firmware/ZiGate-V1/ folder I can see many firmware versions:

-rw-r--r-- 1 root root 182352 Jun 25 2021 ZiGate_Pluzzy_HA1.2v2100.bin
-rw-r--r-- 1 root root ...

Working perfectly now - thanks!

Thanks for the response. Upgraded to .2

Different error this time:

2022-01-10 21:12:56.104 Status: Zigate: (Zigate) onDeviceRemoved - removing End Device
2022-01-10 21:12:56.108 Status: Zigate: (Zigate) Device Zigate - ZB-DoorSensor-D0003_Voltage-84fd27fffe697391-01 with IEEE: 84fd27fffe697391 ...

I recently upgraded the Zigate firmware to 0321 and took the plunge to the new OPDM version so had to re-pair all my devices which has (mostly) gone smoothly.

I upgraded to the latest Zigate plugin at same time 6.0.001

My Linkind Door and Window sensors would re-register when I re-did the pairing ...

Upgraded to latest beta 5.5.290 and restarted domotiz
I removed all four of the selector switches from Domoticz and then re-paired.

Same behaviour as before.
Only the top-left button does anything.
Nothing in the domoticz or plugin log when I press the other buttons.

It would seem the device isn't ...

Great progress with new beta of Zigate plugin.

The device now appears in Domoticz as four selector switches each with click/double-click/long-click options

However only one button (the top left) registers anything in Domoticz.

This button only works after I put the switch into 'scene switch ...

Edit 11/1/21 - just to say this is resolved - see later post

Does anyone have any idea on making this device work nicely with Zigate?
I would just throw it in the bin but there aren't any other good 4 button scene controllers known to work and this also looks quite neat (available in different ...