I have domoticz and a network with about 13 nodes. The Zwave heatmap from domoticz looks like this. zwave.png Number 13 is a zwave Wallswitch (Heiman) and node 019 is a range extender. I am not a zwave specialist, but it looks like node 13 isn't connected to any other neighbour node. When I sent a ...

I have a Fibaro Floodsensor. I Included this device a couple of weeks ago. After testing everything was working ok. But now the node stops signaling. The last time the device had send his information was 05-04 (the date is now 15-04). When I put the node in the water, a signal is heard (flood alert ...

EddyG wrote: ↑Friday 03 April 2020 19:06 Why delete the other devices? Are they in the way? They do no harm!

Good suggestion, I removed them from the active switches, they are still available as devices not in use. But I do not know what to do with them except the one mentioned wiih x00 extension

I think I found the problem. I moved the doorswitch to another door (different magnet). The switch opens now and then. I suspect reed contact in the switch is faulty. WHe I try to open and close 15 times, sometimes it counts just 12 times.

Thank you for your reply. I also have five devices (i counted wrong). I deleted all the others except the one with '00' at the end. The switch stays open (regardless if I open or close the door). There is no entry's found in the logfile. I have removed all entries, set the switch to factory default ...

Hi All, I have three Neo Coolcam door switches. Two of them are working correctly, but one of them is not working. When removing this one and making a factory reset. I add it using the node include. The devices is recognized and I get three sensors. I add them all to the dashboard (Doorswitch1a ...

mickeyr61 wrote: ↑Tuesday 06 November 2018 20:58 Shouldn't they be in the temperature tab or something?

I just got a brainwave. In the settings I pushed the 'Allow devices for 5 minutes button' then reinstalled the buienradar plugin. And voila, the devices appeared under the devices tab. Problem solved

mickeyr61 wrote: ↑Tuesday 06 November 2018 20:58 Shouldn't they be in the temperature tab or something?

No, I checked every tab, but there are no buienradar devices.

I installed the buienradar plugin and followed the steps on gitbub. Everything looked fine, there are no errors and in the Hardware tab in Domoticz the buienradar is found and activated. But in the devices list, there are no devices created. I removed all the files, restarted domoticz and ...

I have updated the firmware of the RFXcom receiver / transmitter (to version 1025) and now something is happening. When I move the magnet from the switch. The status of the switch is going to "Alarm". When I put the magnet next to the detector it says "Motion". Because when the door is closed the ...

I cannot set a delay. I only have a couple of fields available:



There is no field for specifying the off delay.

I just bought a couple of cheap 433Mhz doorsensors, running on a AAA battery. I am trying to get them to work with Domoticz. When I put the battery in, and allow Domoticz to allow new devices. The switch is found in Domoticz. The type is Security, X10 Security, security (device ID CC2800). When I ...

I have installeren the HE863 dusk sensor. It is recognised by domoticz, but the sensor looks tot be switched on allways regardless if it is dark or light. The only thing i can adjust in the device is the hours (between 1 and 8). My Idea was trigger a script when it went dark. Anyone knows this ...

I have both running. But I started with Raspberry Jessie with domoticz and installed kodi later Yes, that did the trick! I was first installing OpenElec and then tried to install domoticz. Now I first installed (through Noobs) raspbian lite and domoticz (this was very simple) and then kodi ...

I have one PI3 and I wondered if it is possible to run Domoticz and Kodi on the same device. I have installed the KAOSBOX image but installing domoticz with sudo curl -L install.domoticz.com | sudo bash does not work.

That did the trick! Thank you very much!

I use the following script for the motion detector (from the Wiki) -- ~/domoticz/scripts/lua/script_device_PIRs.lua commandArray = {} tc=next(devicechanged) v=tostring(tc) if (v:sub(1,3) == 'PIR') then c=v:sub(4) commandArray[c] = 'On' tmess = c..' On - time 0' print(tmess) end return commandArray ...

I made a cable (like this one found here http://blog.hekkers.net/2011/03/14/reme ... revisited/ ). I think the cable is working OK, but I cannot get any data from the Remeha Calenta 40W. I have used the official Remeha program and the OTMonitor program. Any tips?

Ray, thanks for yoyr reply. I have changed the last two digits to .36 and now the Parameter HDUsed is 116. But HDFree and HDFreePerc stay 0.

Thank you for this nice script! It alsmost is working. I get Temperature-1 en 2, CPU, but NAS free space is 0Mo, and Disk space also. I have read the parameters en they are the following values: HDUnit=4096, HDtotal= 64239, HDUsed=1, HDFree=0, HDFreePerc=0. When I try to manual read the line HDUsed ...