Cheap chinese z-wave products

[trixwood]

PD01ZE not PD01TE I hope, pfff...

I hope I get my money back...
how to you make a case by ali without getting into an argument with the shop?

[Derik]

PD01ZE not PD01TE I hope, pfff...

I hope I get my money back...
how to you make a case by ali without getting into an argument with the shop?

ScreenShot181.jpg (12.31 KiB) Viewed 3166 times

ScreenShot182.jpg (16.24 KiB) Viewed 3166 times

ScreenShot183.jpg (25.81 KiB) Viewed 3166 times

And say you ask a Eu version or something else...
Say refund only because the shippingcost are more then the item cost..

Wait a few days.
Perhaps sometimes not al the money... most of time

[Derik]

mmm..
Did the old Rob trick..
First exclude and then include....

And yes..
4 switches and a LUX sensor....!
And battery life...

ScreenShot185.jpg (30.16 KiB) Viewed 3170 times

ScreenShot184.jpg (17.14 KiB) Viewed 3170 times

ScreenShot189.jpg (41.73 KiB) Viewed 3167 times

Only i do not understand a %^$^*%$*%^of that OZW xml story...[ my englisch is to bad ]
Perhaps some one will help me to make this
So i can send it to OZW.

[trixwood]

Yeah, I send a present to a friend of my in hong kong, 25 euro to track and trace to china for a light package as big as a cola can, I was like

[Derik]

And no settings...
Perhaps tomorrow... [ must wait more the 12 hours.. for zwave]

ScreenShot186.jpg (28.26 KiB) Viewed 3165 times

Or is this after add to OZW vissable?

ScreenShot190.jpg (31.07 KiB) Viewed 3163 times

[LouiS22]

And no settings...
Perhaps tomorrow... [ must wait more the 12 hours.. for zwave]
ScreenShot186.jpg

Or is this after add to OZW vissable?

ScreenShot190.jpg

Have you read my post?

[Derik]

And no settings...
Perhaps tomorrow... [ must wait more the 12 hours.. for zwave]
ScreenShot186.jpg

Or is this after add to OZW vissable?

ScreenShot190.jpg

Have you read my post?

This part:

Here's the extract of the manual: http://www.pepper1.net/zwavedb/device/894, one can make the xml for OZW.

Yes..
Only that is the part i do not understand...

[trixwood]

Two have to create/combine/set them on fire/alter/edit existing xml files...

somebody should write a howto: how to edit openzwave xml files... or maybe there is already something out there describing it...

https://github.com/OpenZWave/open-zwave ... ng-Devices

good luck!

[LouiS22]

And no settings...
Perhaps tomorrow... [ must wait more the 12 hours.. for zwave]
ScreenShot186.jpg

Or is this after add to OZW vissable?

ScreenShot190.jpg

Have you read my post?

This part:

Here's the extract of the manual: http://www.pepper1.net/zwavedb/device/894, one can make the xml for OZW.

Yes..
Only that is the part i do not understand...

Derik, I've commited the xml into OZW. It's not yet merged into the master, but hopefully it won't take long. Note, this doesn't mean you can fully use, because first gizmocouz have to update the OZW built into Domoticz. Of course you can put the relevant files into their correct location, but this is a temp solution and you have to repeat it every time you upgrade Domoticz.

[Derik]

Have you read my post?

This part:

Here's the extract of the manual: http://www.pepper1.net/zwavedb/device/894, one can make the xml for OZW.

Yes..
Only that is the part i do not understand...

Derik, I've commited the xml into OZW. It's not yet merged into the master, but hopefully it won't take long. Note, this doesn't mean you can fully use, because first gizmocouz have to update the OZW built into Domoticz. Of course you can put the relevant files into their correct location, but this is a temp solution and you have to repeat it every time you upgrade Domoticz.

Thanks
I"am a "Bouwvakker", and no ICT expert

[cogliostrio]

I updated OZW today, and these popped up. Any feedback on how they work?

[Skippiemanz]

Normally exclude and include should do it. But i dont know where these files are. Perhaps you need to copy them into your zwave domoticz config folder

[Derik]

when these files are not in to Domoticz core..
After an update the files are gone...

[Derik]

Could you not just order from alibaba? They accept paypal and have 1 piece items.

https://szneo.en.alibaba.com/productgro ... ensor.html
https://szneo.en.alibaba.com/product/60 ... _Wifi.html
https://szneo.en.alibaba.com/product/60 ... ntrol.html

Whe can buy 10 pieces... whit all ....

[LouiS22]

I updated OZW today, and these popped up. Any feedback on how they work?

The Power Plug is working as it should . The Door Sensor is still on its way from China, so don't have any feedback on that.

[LouiS22]

when these files are not in to Domoticz core..
After an update the files are gone...

Yes, that's normal - but I wrote you that before. But you can always copy back them if you want to use these devices. Eventually they'll be in domoticz, we just have to wait.

[Derik]

when these files are not in to Domoticz core..
After an update the files are gone...

Yes, that's normal - but I wrote you that before. But you can always copy back them if you want to use these devices. Eventually they'll be in domoticz, we just have to wait.

I now ...
I mean this to.

Code: Select all

cogliostrio 

And the EYE is working great to.
Incl the LUX!!!.. [ sleep when no differences... battery save ]

[LouiS22]

Shenzen NEO's stuff are in the latest beta.

[Derik]

Shenzen NEO's stuff are in the latest beta.

Great....!!!

Only Domoticz does not reconice the sensor?

ScreenShot001.jpg (64.92 KiB) Viewed 2867 times

And unfortunately..
Only now the are expensive..
Almost like all other Zwave devices

[LouiS22]

Shenzen NEO's stuff are in the latest beta.

Great....!!!

Only Domoticz does not reconice the sensor?
ScreenShot001.jpg



And unfortunately..
Only now the are expensive..
Almost like all other Zwave devices

You have te exclude first, then include it again... Also, the latest BETA is .560, yours is still .541...