Can't get Netfit Easy to run

[hjzwiers]

I can't get nefit easy to run, installed through dockge

services:
nefiteasy-http-server:
ports:
- 3000:3000
container_name: myNefitEasy
environment:
- NEFIT_SERIAL_NUMBER=XXXXXX
- NEFIT_ACCESS_KEY=XXXXXXXXX
- NEFIT_PASSWORD=XXXXXX
image: trafex/nefiteasy-http-server
networks: {}

It says in Domotics: Error: Nefit_Easy: Error getting http data! I don't know what to do anymore

Edit Waltervl: removed credentials

[eddieb]

edit you access-key ...

[hjzwiers]

I don't understand, how must I edit the access-key?

[waltervl]

Does it run in Docker? What does the log of the docker say?
Did you stop the normal nefit-easy server on your system?

And stop posting credentials like ID and password/PIN codes on the internet!!!!!

[hjzwiers]

Sorry about the credentials ....

dockge says:

[email protected] start
myNefitEasy | > easy-server --host=0.0.0.0
myNefitEasy |
myNefitEasy | HTTP server listening on http://0.0.0.0:3000

no other comments, I do wonder why its not sending on http://127.0.0.1:3000? Can you put that in the docker file?

[waltervl]

That probably depends how the docker image has been created.....
Does it even work properly?
In the NefitEasy wiki page https://wiki.domoticz.com/NefitEasy there is a troubleshooting part.

Code: Select all

curl http://127.0.0.1:3000/api/status

It should give a valid JSON result.

You can also try

Code: Select all

curl http://0.0.0.0:3000/api/status

or

Code: Select all

curl http://<Domoticz Server IP>:3000/api/status

If one of these works then you have to change the settings accordingly in Domoticz.
If you run Domoticz also in a Docker you probably have to change the settings anyway as 127.0.0.1 is the localhost IP in the container and not of the Domoticz server.

[hjzwiers]

I know I have to change the settings .... but which

curl http://127.0.0.1:3000/api/status:

{"user mode":"manual","clock program":"auto","in house status":"ok","in house temp":27,"hot water active":true,"boiler indicator":"off","control":"weather","temp override duration":0,"current switchpoint":32,"ps active":true,"powersave mode":true,"fp active":false,"fireplace mode":false,"temp override":false,"holiday mode":false,"boiler block":null,"boiler lock":null,"boiler maintenance":null,"temp setpoint":15,"temp override temp setpoint":17,"temp manual setpoint":10,"hed enabled":null,"hed device at home":null,"outdoor temp":30.3,"outdoor source type":"physical"}hjz@debian:/opt/stacks/domoticz/config/plugins/iDetect$

seems all fine

I checked internet and they all show the same settings in the docker file, which one to change?

[waltervl]

You are running Domoticz also in a docker?
Find the real IP of your Domoticz server by open up a terminal window and execute the command:

Code: Select all

ifconfig -a

Then you have to change in Domoticz menu Setup - Hardware - NefitEasy hardware gateway http://127.0.0.1:3000 into http://<Domoticz Server IP>:3000

[hjzwiers]

That was very simple ... but most things are if you know where to look.

Working!

[waltervl]

That was very simple ... but most things are if you know where to look.

Working!

It is more that you have to understand what is happening when you use docker.....