Looking after temperature sensor

Moderator: leecollings

Post Reply
YellowSky
Posts: 65
Joined: Tuesday 12 May 2015 12:09
Target OS: Raspberry Pi / ODroid
Domoticz version: Last
Location: Belgium
Contact:

Looking after temperature sensor

Post by YellowSky »

Hello,
I'm looking for new temperature sensors for my RFXCom.
- I currently have 3 bressers (one per channel) => I'm afraid that by buying a new one, it will parasitize the old ones: do you have any feedback on this?
- a Digoo, but the humidity doesn't rise properly and there's no local display
- a bangood SKU174397 but requires manual reconfiguration when changing the battery

=> Would you suggest another type of probe that, like the Bresser
- has a digital display
- doesn't require reconfiguration when changing batteries
- is not too expensive

Thank you
Toulon7559
Posts: 843
Joined: Sunday 23 February 2014 17:56
Target OS: Raspberry Pi / ODroid
Domoticz version: mixed
Location: Hengelo(Ov)/NL
Contact:

Re: Looking after temperature sensor [for use with RFXCom]

Post by Toulon7559 »

5channel-version from Bresser might be compatible, like
Typenumber: 7009993
EAN: 4007922152097
WEEE-Reg.-Nr. DE 34323861

This device also a candidate:
from TFA offered as replacement for obsolete type 30.3150, modified by Seller for larger range coverage .....
.
Attachments
30.3150 and 30.3245.02
30.3150 and 30.3245.02
TFA_303150_30324502 [640x480].jpg (52.3 KiB) Viewed 674 times
Last edited by Toulon7559 on Tuesday 19 November 2024 14:28, edited 4 times in total.
Set1 = RPI-Zero+RFXCom433+S0PCM+Shield for BMP180/DS18B20/RS485+DDS238-1ZNs
Set2 = RPI-3A++RFLinkGTW+ESP8266s+PWS_WS7000
Common = KAKUs+3*PVLogger+PWS_TFA_Nexus
plus series of 'satellites' for dedicated interfacing, monitoring & control.
b_weijenberg
Posts: 517
Joined: Friday 12 July 2013 18:13
Target OS: -
Domoticz version:
Location: Netherlands
Contact:

Re: Looking after temperature sensor

Post by b_weijenberg »

The FT007TH could be used. This sensor has up to 8 fixed channels.
https://www.conrad.nl/nl/p/renkforce-ft ... 25532.html
RFXtrx433, RFXtrx433E, RFXtrx433XL, RFX433XL, RFX868XL
YellowSky
Posts: 65
Joined: Tuesday 12 May 2015 12:09
Target OS: Raspberry Pi / ODroid
Domoticz version: Last
Location: Belgium
Contact:

Re: Looking after temperature sensor

Post by YellowSky »

Thanks for your suggestion
YellowSky
Posts: 65
Joined: Tuesday 12 May 2015 12:09
Target OS: Raspberry Pi / ODroid
Domoticz version: Last
Location: Belgium
Contact:

Re: Looking after temperature sensor

Post by YellowSky »

b_weijenberg wrote: Friday 08 November 2024 10:22 The FT007TH could be used. This sensor has up to 8 fixed channels.
https://www.conrad.nl/nl/p/renkforce-ft ... 25532.html
This sensor is decoded with which firmware of RFXCOM while i can't see them on mine?
b_weijenberg
Posts: 517
Joined: Friday 12 July 2013 18:13
Target OS: -
Domoticz version:
Location: Netherlands
Contact:

Re: Looking after temperature sensor

Post by b_weijenberg »

Enable the Oregon protocol.
The very old (>10Yr) RFXtrx433 doesn't support this sensor.
Use Pro1 firmware in the RFXtrx433E.
All firmware of the RFXtrx433XL and RFX433XL supports this sensor.
RFXtrx433, RFXtrx433E, RFXtrx433XL, RFX433XL, RFX868XL
YellowSky
Posts: 65
Joined: Tuesday 12 May 2015 12:09
Target OS: Raspberry Pi / ODroid
Domoticz version: Last
Location: Belgium
Contact:

Re: Looking after temperature sensor

Post by YellowSky »

Hum, perhaps i had one old RFXCOM (i think i bought it in 2018)
Oregon is already enabled

Here is the detailed in domoticz
2024-11-13 19:55:25.557 Firmware version = 1025
2024-11-13 19:55:25.557 Firmware type = Ext
2024-11-13 19:55:25.557 Hardware version = 1.3

Edit: ok i get it, with pro version, i will check if others sensors work again.
Thank you again.

Edit 2: FTR: in my case, i need to use Ext2 version to continue to use Chacon switch while Pro1 and Pro2 version can't transmit command for these switch.
rylfas
Posts: 4
Joined: Monday 10 March 2014 10:17
Target OS: Raspberry Pi / ODroid
Domoticz version:
Contact:

Re: Looking after temperature sensor

Post by rylfas »

An other solution is to install ZIgbee temperature sensors. They all cost less than 10 euro (even available with nice displays).

You only need to install a Zigbee Coordinator and install for instance Zigbee for Domoticz (https://zigbeefordomoticz.github.io/wiki/en-eng/)

In the end a much more cost effective, energy friendly and stable solution
Post Reply

Who is online

Users browsing this forum: No registered users and 0 guests