Somfy Telis Remotes

[SHadley1138]

10;Rts;clean

[piokuc]

Thanks.
But why it not working for me ? What i do wrong ? Why not open and close my somfy if reconized signal ?

And why RC which i send is 0412 but in RFLink save 0413 ?

[SHadley1138]

I had similar problems, Rflink looked OK, but domoticz just wouldn't work

I think the number has increased as its a rolling code, so it changes each time it's used

[piokuc]

Is any chance to fix it and help me to start working with Somfy ? For now not working.

Is anybody who start working it with somfy and can help me ?

[SHadley1138]

I used the dry contacts in the end and bought a cheap relay from eBay

Might have another play today

[piokuc]

But any user use it as write on forum... any help

Anybody run somfy on RFLink with Domoticz ?

[octopuss83]

Hello ,

My blind works ok with rflink with the command : 10;RTS;0100F2;0;DOWN; . I wrote to the rflink developper you must create new remote in EEPROM RFlink address , i see that level is reached on the post ... But it s very important to choose a remote address who not begin by 00.... ; address could be 20.... for example .
In My case Domoticz not send command 10;RTS;0100F2;0;DOWN; to rf link I have a message "Error sending switch command, check device/hardware !"
The other switch works very well.

If you need help on rflink i can help you
if you need help on DomoticZ u can help me

Best regards

[supermat]

HI
I read this manual:
https://matdomotique.wordpress.com/2016 ... -et-somfy/

i send command

Code: Select all

10;RTS;0F0F0F;0412;3;PAIR;

and then i press for about 3 secund button on remote to PROG.
On loader show example

Code: Select all

20;07;OK;

Hi,

You must press for about 3 second on remote to prog AND THEN send the command to pair

Code: Select all

10;RTS;0F0F0F;0412;3;PAIR;

The blind must be in prog mode to register the "new remote".

The RC is the rolling code, it do +1 for each command send and pairring is a command.

[piokuc]

Hi i pressed about 3 sec.

But after i prog RFLink then i must also prog Blinds by send command from RFLink ? But after that Remote will stop working ? Now my remote works ok with blinds.

[piokuc]

Is anybody who can write step by step how configure Somfy with RFLink to working in Domoticz ? Please....

[SHadley1138]

I've tried loads to get this to work, but just can't get it to work. I can program it into Rflink using the loader, but I just can't get it to work


Sent from my iPhone using Tapatalk

[piokuc]

Hi
I do all as write in manual:
https://matdomotique.wordpress.com/2016 ... -et-somfy/
and i tested without rooling code (correct in manual one day ago) and problem is the same. Blinds run for some seconds (maybee 3 to 5 seconds) and stop. Send command again , run again blinds only for 3-5secund and stop. But command should run blind to close full window. Why working only some secunds ?

I send command:

Code: Select all

10;RTS;02FFFF;3;DOWN;

From remote SMOOVE ORIGIN RTS works ok. When i click button DOWN blinds run and full close my window.
Please help.

[bananig]

Hi piokuc,

did you ever solve your issue?
it is the same for me. i could setup the rflink and can send UP and DOWN commands, but the blinds only run for a few seconds and then stop, instead of completing up/down to the end.
would appreciate your help.

[javicalle]

I think that the problem can be related to this:

• https://community.home-assistant.io/t/r ... /187904/16

[hoeby]

I have 2x somfy tilt 50 venetian blind motors.
I tried and googled and tried. But couldn't get it to work propperly. What i did, was connecting a device with espeasy to the pcb (solder). Works without issues. Rf-link is disconnected and dropped in a box.

Maybe not what you would like to hear. Hopefully for you, you can find the answer to it.

[homeJLB]

I have a RFX-com-XL and before a RFX-com-E both connected to 9 Somfy blinds. they worked for over 5 years now. But now the board is crashed (tinker board + tinker board OS) and I'm putting everything over on Raspberry Pi4 - 4. I to had some trouble reconnecting the new Domoticz and rfx to the blinds. So I cleared all remote in the RFX and I reset the Blinds with the 3-8-3 method. now all is working again. For RF-link I have no experience

@hoeby; what do you meen by disconnected and dropped in a box.

[hoeby]

@hoeby; what do you meen by disconnected and dropped in a box.

That i don't use rf-link anymore. I only used it for somfy, but it didn't worked perfect on blinds,
Disconnected it from the pi and put it away