Moderators: leecollings, remb0
Code: Select all
Sensitivity Level Setting: 12
On/Off Duration: 30 second
Basic Set Level: 255
PIR Detecting Function Enabled:
Ambient Illumination Lux Level: 100 lux
Re-trigger Interval Setting: 8 second
Light Sensor Polling Interval: 360 second
Lux Level Function Enable: Disable
Ambient illumination Lux Level Report: 5 lux
Led Blink Enable: Disable
I use rechargeable (2200mA) Li-ion batteries and they will last a few months.FearNaBoinne wrote:I have 2 Neo Coolcam 2-in-1 PIR/Lux sensors (Z-Wave) and they run through (very expensibe CR123A) batteries like crazy!!
Where did you buy those? I might be interested in those, but still wondering why a Duracell CR123A only lasts ~2 weeks...
Can you contact the seller about this? Maybe the device is broken... Just a question... they all say you can do around 1 year on 1 battery....FearNaBoinne wrote: ↑Saturday 06 July 2019 20:43 Not very encouraging...
It's only 5 days, as that's when I installed the battery plugin to track it...
[Battery level over time - battery replaced on 28 June]
)
Really? Do you think so? I would've never guessed!
1. Motion detection sensitivity: Normal
Adapt the sensitivity of the motion detection.
Last Update: 2020-05-06 02:53:53
2. Motion detection ON time: 300
(second) (actual: 300)
This parameter can be determined how long the associated devices should stay ON status. For instance, this parameter is set to 30(second), the PIR detector will send a BASIC_SET Command to an associated device with value basic set level if PIR detector is triggered and the associated device will be turned on 30(second) before it is turned off. This Parameter value must be large than Parameter 6#. If user set this parameter to default by Configure CC, the parameter #6 will be set to default value. Available Settings:5 to 600(second).
Last Update: 2020-05-06 02:53:53
3. Basic Set Level: 255
(actual: 255)
Basic Set Command will be sent, on the associated devices (group 2), where contains a value when PIR detector is triggered, the receiver will take it for consideration; for instance, if a lamp module is received the Basic Set Command of which value is decisive as to how bright of dim level of lamp module shall be. This Parameter is used to some associated devices. Available Settings: 0, 1 to 99 or 255.
Last Update: 2020-05-06 02:53:53
4. Motion detection function: Enable
Enable the motion detection (PIR) function. This parameter does not effect the luminance reporting.
Last Update: 2020-05-06 02:53:53
5. Ambient Illumination Lux Level: 0
(lux) (actual: 0)
Define the illumination level value which determines when the 'Illumination switch ON function' is activated. If the illumination level falls below this value and a person moves across or within the detected area, the motion sensor will switch on the associated device (group 2). 0 to 1000(Lux).
Last Update: 2020-05-06 02:53:53
6. Motion detection blind time: 8
(second) (actual: 8)
Period after motion detection in which the sensor is insensitive for new motion detection. This value must be less than the 'Motion detection ON time'. Available Settings: 1 to 8(s).
Last Update: 2020-05-06 02:53:53
7. Illumination reporting interval: 3600
(second) (actual: 3600)
Determine the time between illumination reports, even when value has not changed. NOTE: This Value Must Be less than Wakeup Interval Time. Available Settings: 60 ~ 36000(second).
Last Update: 2020-05-06 02:53:53
8. Illumination function: Disable
Enable the function to switch on a associated device (group 2) once motion has been detected and the illumination level will be less than the value specified in 'Illumination switch ON level'.
Last Update: 2020-05-06 02:53:53
9. Illumination report threshold: 100
(lux) (actual: 100)
This parameter defines by how much Lux Level must change, in lux, to be reported to the main controller.
Last Update: 2020-05-06 02:53:53
10. Ambient Temperature Differential Level Report or Led Blink Enable (0 or 1 - non-temperature version): 5
(0.1 C) (actual: 5)
This parameter is configured the value that differential between current measured and previous report value. If the differential value larger than the settings, device will report this measured temperature value to nodes associated in lifeline.
Last Update: 2020-05-06 02:53:53
11. Led Blink Enable (temperature reporting version): Enable
This parameter can enabled or disable the PIR led blinking function.
Last Update: 2020-05-06 02:53:53
12. Motion Event Report One Time Enable (temperature reporting version): Only Once
The motion detected event can be sent multiple times/only once until device report motion cleared event.
Last Update: 2020-05-06 02:53:53
99. Ambient Light Intensity Calibration: 5320
(actual: 5320)
This parameter defines the calibrated scale for ambient light intensity.
Last Update: 2020-05-06 02:53:53
2000. Wake-up Interval: 43200
(Seconds) (actual: 43200)
How often the Device will Wake up to check for pending commands
Users browsing this forum: No registered users and 1 guest