Tip: Cheap wireless doorbell from Action

[m00st]

A tip for Dutch Domoticz users: the Select Plus wireless doorbell that's for sale for 5,95 Eur at the Action works well with RFXcomm, provided that you enable the Byron SX protocol on the RFXcomm.:


This is the unit in it's packaging:


It comes with a remote door clicker (battery included) and the receiver (the thing that makes the sound) plugs into an EU power socket. It has 3 volumes and 36 different melodies. Pretty handy as a chime for some event.

[EdwinK]

Thanks. Going to get me some later.

[SteGe]

That is working for me as well. I have it as a trigger for getting a snapshot of my security camera and send it to my whatsapp.

But when I trigger it in Domoticz, the chime is ringing as well (and so annoying my Girlfriend when testing the system haha)

[TyzzyT]

This is awesome!
I was looking for a cheap device which could alarm me in case of fire, waking up, etc. This is exactly what I was looking for.

Is it possible to make the doorbell and the siren both a seperate sensor in Domoticz? So I can have a seperate doorbell switch and a seperate siren for multiple applications?

[Dirk]

Thanks for sharing! This Action doorbell works for me to. I have not looked into un-pairing the doorbell and the chime, would be nice to be able to use the doorbell as a remote-control for other domoticz actions.

[Snakfy]

Thanks for the Tip!
I'm going to have a look tomorrow if they still have it.

[Chillout]

I got this exact model last week. So far, I haven't been able to get it working...

[freijn]

for the RFLinkGateway the doorbell is working the sirene can not be triggered by the Domoticz system

[Dirk]

I got this exact model last week. So far, I haven't been able to get it working...

Did you enable the correct protocol? (the Byron SX protocol on the RFXcomm according to the first post).

[jelledj]

Are there separate low cost doorbell buttons (beldrukker < dutch) with integrated light that I can connect to my wired cables of my current doorbell connected to the transformer in my utility room, that will be able to create an event in domoticz (RFZcomm?)

[Scalyvo]

Hi All,

My setup : platform raspberry2 with domoticz v3.8153
RFXCOM - RFXtrx433 USB 433.92MHz Transceiver
Version: Ext2/1024

I have the Byron SX protocol enabled by (Modus instellen) and click the set mode button .

When i want to add new hardware, the Byron sx protocol is not in the (Type) list to select .

What can i do more ?

Greetzzz
Scalyvo

[Eddiever]

Use the Learn Light/Switch and then push the button. This should show your new button/doorbell.

[Scalyvo]

Use the Learn Light/Switch and then push the button. This should show your new button/doorbell.

Thnx problem solved !

[Dirk]

Note that these doorbells are in & out of stock often at Action. So if you don't find them now, try again in a few weeks or try another Action. Utrecht currently doesn't sell them but Amsterdam does.

[gschmidt]

I have also same doorbell, created a switch for it with rfxtrx433xl (lighting 4) modus added. When I hit the doorbell switch there is only one record in the log, but when I push the physical doorbell button there are 3 or 4 records in the log???...I want to sent a notification but not 3 or 4...is there a trick for this?

[wvries]

I have also same doorbell, created a switch for it with rfxtrx433xl (lighting 4) modus added. When I hit the doorbell switch there is only one record in the log, but when I push the physical doorbell button there are 3 or 4 records in the log???...I want to sent a notification but not 3 or 4...is there a trick for this?

did you figure this out already ?
within dzvents, use the lastUpdate check.

Code: Select all

if (domoticz.devices('Frontdoor Bel').changed and domoticz.devices('Frontdoor Bel').lastUpdate.minutesAgo > 1) then
"Action"
end