You need to set off delay. I've set it to 10 seconds but you can use what ever suits you.SteGe wrote:I also ordered the Oudi door sensor. But when I add it as a switch it only turn on, and never gets off (also won't turn off when I click it by hand). Should I change it to another type of switch?
Low cost window/door sensor
Moderator: leecollings
-
- Posts: 10
- Joined: Wednesday 11 November 2015 13:11
- Target OS: Raspberry Pi / ODroid
- Domoticz version: 2.3530
- Location: Finland
- Contact:
Re: Low cost window/door sensor
- Attachments
-
- Screen Shot 2016-09-08 at 6.30.45 PM.png (168.12 KiB) Viewed 4805 times
-
- Posts: 40
- Joined: Saturday 02 July 2016 13:54
- Target OS: NAS (Synology & others)
- Domoticz version: Beta
- Location: Netherlands
- Contact:
Re: Low cost window/door sensor
Thx, that's works! Now I'm getting a notification when somebody opens my postbox. Will get a camera in the near future so that I can get a picture when somebody is at the door or opens the letterbox.
Synology DS3615xs | Raspberry pi 3b |
RFXtrx433E | MySensors | Z-wave | Philips Hue | Ikea Tradfri |
Sunscreen | Power switches | Toon | Harmony | UE Smartradio |
Weatherstation | Doorbell | Letterbox reader | Lux | Temp | Humidity | Motion |
RFXtrx433E | MySensors | Z-wave | Philips Hue | Ikea Tradfri |
Sunscreen | Power switches | Toon | Harmony | UE Smartradio |
Weatherstation | Doorbell | Letterbox reader | Lux | Temp | Humidity | Motion |
-
- Posts: 9
- Joined: Friday 11 July 2014 10:46
- Target OS: Raspberry Pi / ODroid
- Domoticz version:
- Contact:
Re: Low cost window/door sensor
Hi all !
I just found this product : https://fr.aliexpress.com/af/detecteur- ... lanktest=0
Do you know if it is compatible with Domoticz , if yes, which protocol.
Do you know if it send ON and OFF signal to notify when a door is open and when it is closed?
Thx !
Bastien
I just found this product : https://fr.aliexpress.com/af/detecteur- ... lanktest=0
Do you know if it is compatible with Domoticz , if yes, which protocol.
Do you know if it send ON and OFF signal to notify when a door is open and when it is closed?
Thx !
Bastien
-
- Posts: 16
- Joined: Thursday 27 October 2016 22:36
- Target OS: Raspberry Pi / ODroid
- Domoticz version:
- Contact:
Re: Low cost window/door sensor
just bought this sensor and can report it's working ok with RFLink and Domoticz. Battery (23A) was included altough not clearly specified. Just ordered another two of these. mounted it in my snail mail box by soldering a wired reed contact so it fitted better and the main unit could be mounted on the inside of the door. Don;t know yet about battery life, but we'll see. Noticed some other sensors in Domotics device list that are probably the same (ev1527 and eurodomest) with some similar codes...
- Treve
- Posts: 107
- Joined: Thursday 05 November 2015 10:37
- Target OS: Raspberry Pi / ODroid
- Domoticz version: v4.11474
- Location: Rotterdam, NL
- Contact:
Re: Low cost window/door sensor
Witch signal generates this sensor? on/off, on or off?jackderuiter wrote:just bought this sensor and can report it's working ok with RFLink and Domoticz. Battery (23A) was included altough not clearly specified. Just ordered another two of these. mounted it in my snail mail box by soldering a wired reed contact so it fitted better and the main unit could be mounted on the inside of the door. Don;t know yet about battery life, but we'll see. Noticed some other sensors in Domotics device list that are probably the same (ev1527 and eurodomest) with some similar codes...
- RFXtrx433E,
- AEON Labs ZW090 Z-Stick Gen5 EU
- Hue v2.1
- Raspberry Pi 3 Model B, Raspbian Stretch Full on USB-Stick.
- Domoticz 4.11474
Devices: KaKu, Z-Wave, Hue.
for testing:
Raspberry 4, 2GB, SSD
Domoticz 2022.1
Ikea Hub, Fyrtur curtain
- AEON Labs ZW090 Z-Stick Gen5 EU
- Hue v2.1
- Raspberry Pi 3 Model B, Raspbian Stretch Full on USB-Stick.
- Domoticz 4.11474
Devices: KaKu, Z-Wave, Hue.
for testing:
Raspberry 4, 2GB, SSD
Domoticz 2022.1
Ikea Hub, Fyrtur curtain
-
- Posts: 16
- Joined: Thursday 27 October 2016 22:36
- Target OS: Raspberry Pi / ODroid
- Domoticz version:
- Contact:
Re: Low cost window/door sensor
only on. However somtimes ip pops up as a ev1527 and then as eurodomest, both with other id's so don't know if it's a domoticz/rflink/transmitter issue.. Worked ok last week, but since this weekend it switched ID..
-
- Posts: 16
- Joined: Thursday 27 October 2016 22:36
- Target OS: Raspberry Pi / ODroid
- Domoticz version:
- Contact:
Re: Low cost window/door sensor
Just received another 433 door contact with ev1527. really Nice casing compared to some other uggly Chinese door sensors. Don't know yet about battery Life ofcourse but we will see. Only reporting on signal as usual with these sensors.
Re: Low cost window/door sensor
I bought several Kerui D026, they are cheap and are looking very nice! Works fine with domoticz + RFX
-
- Posts: 14
- Joined: Tuesday 19 July 2016 14:49
- Target OS: Raspberry Pi / ODroid
- Domoticz version: 3.9227
- Location: Italy
- Contact:
Re: Low cost window/door sensor
Does the kerui d026 generate on/off signal?josimd wrote:I bought several Kerui D026, they are cheap and are looking very nice! Works fine with domoticz + RFX
I'm looking for a cheap door sensor able to send an on/off signal
thanks
Domoticz + Mysensors 2.0 ESP8266 GW + RFlink + Philips Hue 2.0 + Netatmo Thermostat
Re: Low cost window/door sensor
Yes, generates an On and Off pulse..
Verzonden vanaf mijn iPhone met Tapatalk
Verzonden vanaf mijn iPhone met Tapatalk
-
- Posts: 14
- Joined: Friday 18 November 2016 8:15
- Target OS: Raspberry Pi / ODroid
- Domoticz version:
- Contact:
Re: Low cost window/door sensor
How did you get it worked with a RFX?josimd wrote:I bought several Kerui D026, they are cheap and are looking very nice! Works fine with domoticz + RFX
Verzonden vanaf mijn iPhone met Tapatalk
Re: Low cost window/door sensor
How did you get it worked with a RFX?robertje221 wrote:josimd wrote:I bought several Kerui D026, they are cheap and are looking very nice! Works fine with domoticz + RFX
Yes, works with RFX
Verzonden vanaf mijn iPhone met Tapatalk
-
- Posts: 14
- Joined: Friday 18 November 2016 8:15
- Target OS: Raspberry Pi / ODroid
- Domoticz version:
- Contact:
Re: Low cost window/door sensor
How did you add the kerui d026 sensor? Is it protocol lightning 4 and then learning mode or manual mode?josimd wrote:How did you get it worked with a RFX?robertje221 wrote:josimd wrote:I bought several Kerui D026, they are cheap and are looking very nice! Works fine with domoticz + RFX
Yes, works with RFX
Verzonden vanaf mijn iPhone met Tapatalk
Verzonden vanaf mijn iPhone met Tapatalk
Re: Low cost window/door sensor
Yes lightning 4 (hardware tab) after sensing the kerui it will apear in 'apparaten'robertje221 wrote:How did you add the kerui d026 sensor? Is it protocol lightning 4 and then learning mode or manual mode?josimd wrote:How did you get it worked with a RFX?robertje221 wrote:
Yes, works with RFX
Verzonden vanaf mijn iPhone met Tapatalk
Verzonden vanaf mijn iPhone met Tapatalk
Verzonden vanaf mijn iPhone met Tapatalk
-
- Posts: 41
- Joined: Saturday 12 December 2015 13:25
- Target OS: Raspberry Pi / ODroid
- Domoticz version:
- Contact:
Re: Low cost window/door sensor
I bought some Kerui-like sensors form AlieExpress, and connected them yesterday without any problems. (PT2262, lightning 4)
That is.... 3 of 5 connected flawless when I used the learning mode.
But 2 of the sensors won't connect, no matter what I try, the sensor has a red led which flashes when activated (sensor disconnects), and that still works, I only get so see the hiddious "Time Out, Try again" in Domoticz.
Any suggestions what I could try?
That is.... 3 of 5 connected flawless when I used the learning mode.
But 2 of the sensors won't connect, no matter what I try, the sensor has a red led which flashes when activated (sensor disconnects), and that still works, I only get so see the hiddious "Time Out, Try again" in Domoticz.
Any suggestions what I could try?
-
- Posts: 517
- Joined: Friday 12 July 2013 18:13
- Target OS: -
- Domoticz version:
- Location: Netherlands
- Contact:
Re: Low cost window/door sensor
@ArieKanarie: please check with RFXmngr with only Lighting4 and undec on enabled. If you don't receive all contact support rfxcom.com
On request a beta version Ext2 firmware is available for real Kerui sensors to receive these sensors as security sensor.
On request a beta version Ext2 firmware is available for real Kerui sensors to receive these sensors as security sensor.
RFXtrx433, RFXtrx433E, RFXtrx433XL, RFX433XL, RFX868XL
-
- Posts: 41
- Joined: Saturday 12 December 2015 13:25
- Target OS: Raspberry Pi / ODroid
- Domoticz version:
- Contact:
Re: Low cost window/door sensor
@b_weijenberg
When connected with RFXmngr I can see the messages being transmitted.
Connected the rfxtrx back to the pi, (updated the firmware to 1011) and learning the switch still fails.
When connected with RFXmngr I can see the messages being transmitted.
Code: Select all
------------------------------------------------
------------------------------------------------
Packettype = UNDECODED RF Message
UNDECODED ARC:0CFCE0
------------------------------------------------
------------------------------------------------
Packettype = UNDECODED RF Message
UNDECODED ARC:12DFF380
------------------------------------------------
------------------------------------------------
Packettype = UNDECODED RF Message
UNDECODED ARC:0EFF38
------------------------------------------------
------------------------------------------------
Packettype = UNDECODED RF Message
UNDECODED ARC:12DFF380
------------------------------------------------
------------------------------------------------
Packettype = UNDECODED RF Message
UNDECODED ARC:0BF980
------------------------------------------------
------------------------------------------------
Packettype = UNDECODED RF Message
UNDECODED ARC:0AFC40
------------------------------------------------
------------------------------------------------
Packettype = UNDECODED RF Message
UNDECODED ARC:11BFE700
------------------------------------------------
------------------------------------------------
Packettype = UNDECODED RF Message
UNDECODED ARC:14F7FCE0
------------------------------------------------
------------------------------------------------
Packettype = UNDECODED RF Message
UNDECODED ARC:12DFF380
------------------------------------------------
------------------------------------------------
Packettype = UNDECODED RF Message
UNDECODED ARC:0FFF9C
------------------------------------------------
------------------------------------------------
-
- Posts: 517
- Joined: Friday 12 July 2013 18:13
- Target OS: -
- Domoticz version:
- Location: Netherlands
- Contact:
Re: Low cost window/door sensor
The sensor does not transmit correct Lighting4 packets and is not a Kerui compatible sensor.
Contact support rfxcom.com for further investigation.
Contact support rfxcom.com for further investigation.
RFXtrx433, RFXtrx433E, RFXtrx433XL, RFX433XL, RFX868XL
Re: Low cost window/door sensor
Does this one work with ver1011? Or should I buy real Kerui-sensors? This one should have ON and OFF mode too
https://www.aliexpress.com/item/High-gr ... 2167&tpp=1
https://www.aliexpress.com/item/High-gr ... 2167&tpp=1
RFXcom433e ver1009,Raspberry Pi,Domoticz v3.5877
KaKu:16c remote,dimmer,wall-sockets,sunscreenswitch
Promax:wall sockets Elro:wall sockets Somfy:RFY screens
TFA:weather station Chinese temperature sensors, smoke detectors, power switches
KaKu:16c remote,dimmer,wall-sockets,sunscreenswitch
Promax:wall sockets Elro:wall sockets Somfy:RFY screens
TFA:weather station Chinese temperature sensors, smoke detectors, power switches
-
- Posts: 9
- Joined: Friday 11 July 2014 10:46
- Target OS: Raspberry Pi / ODroid
- Domoticz version:
- Contact:
Re: Low cost window/door sensor
Hi !
I just received these 6 KERUI door sensor and i try to configure it in domotic.
When i open the door, the device "Ouverture chambre" receive a message
When i close the door, the device "
In "Switch" tab ... no update on devices ....
Please can someone post screenshot of his device configuration pls ?
I just received these 6 KERUI door sensor and i try to configure it in domotic.
When i open the door, the device "Ouverture chambre" receive a message
When i close the door, the device "
In "Switch" tab ... no update on devices ....
Please can someone post screenshot of his device configuration pls ?
Who is online
Users browsing this forum: No registered users and 1 guest