Ok, thx, I will check the DeConz logs too.
As you can indeed see from the logs I manually switched the heat pump back on but left the logs entries to show here, for your reference and to contrast the not so well understood log entry.

Hi,

I have a Phoscon Conbee 2 (firmware 26720700) happily functioning on my RPI (on buster) running Domoticz 2022.1. My setup is fairly simple, having a couple of LED lights that I switch on and off manually or through timers in Domoticz using both RFXcom and Zigbee. I am not using any scripting ...

Hi,

Well, if your issues is truely identical do not hesitate to follow Thorgal789's post/instruction. It worked flawlessly in my case.

Regards,

Michel

Dear Thorgal789/Smanar,

I do recognize Smanar indeed from the many places I have visited during my quest for a solution ;-)

Your answer was the silver bullet. I had already tried flashing the stick through my RPI but that did not work (also bit strange). On Windows 11 it worked like a charm, the ...

Hi,

Thanks so much for your reply.

I'm running headless indeed. Deconz service is enabled and running. No error message in (sys)logs other than the one dmesg shows.

Michel.

Hi,

I have Domoticz 2021.1 running on a Pi Model 3b (running buster) and recently attached a Conbee 2 Zigbee USB-stick to it. However:
- Phoscon app tells me "firmware is disconnected" and
- Domoticz (on port 80) is telling me every 10th second: Error: ConbeeStick: (ConbeeStick) Startup failed ...

Hi,

I have followed these steps and actually have a "camera" switch in my dashboard. When I click the actual ipcam picture I do get live videostream, though no preview image(s) in my dashboard icon itself. Yes, I did switch the "Camera previews on the dashboard"-box in settings.

Additionally, I ...

Hi,

Found the issue myself. So I do indeed routinely change sensors, but this time I broke my own routine: I "added" none of the earlier temporary devices to the "used devices" list before replacing the original sensor with the new temporary one. If you do add the temporary device to the "used ...

Hi,

I am using Domoticz v4.10717 on an RPI 3B+ with a couple of Oregon RTGR328N temp+hydro sensors through RFXcom (433). These have been working smoothely for years now. I routinely change batteries for these sensors and, since the sensors change their hardware ID's, I thus routinely follow the ...

Hi Timeless,

And, clearly, I am one of those people. How stupid have I been and how grateful I am for your reply.

I thought that checkbox was still checked...but is was no longer. Now it is again and the new device was added within seconds.

Thx man!!

Michel.

Sure.

I've got the Sensus HRI pulse sensor from: HomeWizard and attached it to one of the pulse inputs of the S0 Pulse Counter Module No direct link, but search for: S0 Pulse Counter Module

S0 Pulse Counter module is already supported by Domoticz, so it could be added without much hazzle ...

Hi,

I am not a hero with copying xml/code into a forum, but let's give it a try. Here is the part from the zwcfg_xxxx.xml for one of my Devolo Radiator Thermostats including its timer configurations :-) Does this help?

</Node>
- <Node id="5" name="Devolo Hal" location="" basic="4" generic="8 ...

And some picture proof...
Regards,

Michel.

Hi,

Sorry for getting involved so late, but yes, I have a Razberry with Devolo Thermostat working properly, except for setting its internal clock. I have proper temp readings (checked that with another thermometer) in Domoticz and I am scheduling temp settings on the thermostat.

So it can work to ...

Hi Blitzkneisser,

Mnay thanks for the extended and detailed answer. In short: works like a breeze after adjustment of the XML, restart and re-include of the thermostat! Now, interestingly I just have one set point device for the thermostat, but it works. The only device that does not work is the ...

Hi Blitzkneisser,

I am struggling with the same issue(s) here! However, I only get one device for the set point. And mine is not updating the physical device as you initially experienced. Also rebooting my Pi did not help.

Can you elaborate on the changes you made to the XML. No clue what XML nor ...

Shortly after my posting here, I performed a reboot of my RaspBerry Pi....after the reboot all 4 devices were available in Domoticz.

Serendipity and case close!

Regards,

Michel.

Hi,

I am on Domoticz 2.3530 and trying to get a Fibaro Wall Plug FGWPE (sold as "Toon Stekker" to be exact) working corretly....meaning: also being able to see energy consumption in Domoticz.

What is going well: associatoin with Domoticz as a node.
What does not look well: I only get three devices ...

Great, that worked wonderfully. Thx!

Michel.

Hi,

My Domoticz on Raspberry is working fine since 1,5 yr, untouched. This week suddenly one gas meter reading wasn't processed correctly. Instead of registering the daily usage Domoticz recorded the actual meter reading as the daily usage, resulting in a daily usage 1000x higher than correct. This ...