Hi all,

I am using for years "pytuya" pluging to get access to TUYA device on local network on my Raspberry PI 3 running Domoticz 2022.1 version under "Buster" OS
I have now decided to install the last version of Domoticz 2025.2 on a new Raspberry PI5 running "Trixie"

Domoticz is running fine but ...

Found the issue with the rain sensor. Please upgrade to beta 16268


Thanks a lot for your support
I have upgraded to version beta 16268 and now I have some values for the Rain sensor in Domoticz.
But some values are not correct compared to the ones from Ecowitt application
The big value of 253,9 ...

Could you please confirm that version 2024.4 of Domoticz should work or should I upgrade to a newer version

No, this is not working as a recent patch has been made.

You have to use the beta version.

Bdw, the stable release is 2024.7 (but you need to use the current beta!)

In the settings you ...

Could you please confirm that version 2024.4 of Domoticz should work or should I upgrade to a newer version

No, this is not working as a recent patch has been made.

You have to use the beta version.

Bdw, the stable release is 2024.7 (but you need to use the current beta!)

In the settings you ...

Seems you receive more devices, like a strike count as well.

Anyway, perform these steps:

- go to hardware, disable the RFXCom hardware
- go to devices, delete all discovered devices for your RFXCom hardware
- go to settings, enable accept new hardware/devices

Now wait until your weather is ...

No new Domoticz version needed...
In menu setup settings ( https://www.domoticz.com/wiki/Application_Settings#System_Setup ) switch off setting "Accept new hardware devices" and press button Apply Settings.
This will prevent new devices are created.
Then remove all unwanted Ecowitt devices except ...

gizmocus told you: "configure domoticz to not accept new hardware/devices in the settings"
This will avoid adding unknown sensors.

Delete all Ecowitt devices except 74B1

Domotics software needs an update to show the other sensors with the same ID 74B1:
ID = 74B1 decimal:29873
Direction = 166 ...

gizmocus told you: "configure domoticz to not accept new hardware/devices in the settings"
This will avoid adding unknown sensors.

Delete all Ecowitt devices except 74B1

Domotics software needs an update to show the other sensors with the same ID 74B1:
ID = 74B1 decimal:29873
Direction = 166 ...

gizmocus told you: "configure domoticz to not accept new hardware/devices in the settings"
This will avoid adding unknown sensors.

Delete all Ecowitt devices except 74B1

Domotics software needs an update to show the other sensors with the same ID 74B1:
ID = 74B1 decimal:29873
Direction = 166 ...

Your RFXCom device is probably receiving sensors from your Neighbours as well, and there could also be some bad reception. (Maybe the device is to far away?)
I would not worry about these, once you got your WS90 sensors added, configure domoticz to not accept new hardware/devices in the settings ...

Hi Patrick,

Together with RFXCom we made some changes, and your Weather device should now work.


After having waited some time I have now a lot of different sensors seen by the RFX868 with even some strange values which do not correspond in any way to the ones from my weather station!
09-09 ...

Hi Patrick,

Together with RFXCom we made some changes, and your Weather device should now work.


Hi,

Sorry for the late reply but I was on hollidays

After your changes what should I change in my configuration ( in RFX868 and/or Domoticz) in order to get the missing sensors ?

I have just ...

I have added another senseor from Ecowitt a WH57 lightning sensor which is recognized and created in Domoticz without any problem
But still only the "wind" sensor created from WS90as shown in the picture
29-08-2024 11-38-06.png

Corresponding data from RFXmngr ...

gizmocuz wrote: Thursday 29 August 2024 8:03 Also try to use the serial-by-id as this is unique through the system, you will get issues when you connect multiple usb devices in the feature as the usb ports might be changed internally after a reboot

Thanks for this advice,I have changed it Regards
Patrick

Thanks for the reply
Please find hereafter the copy of the data from RFXmngr
I hope this can help

Regards
Patrick

================================================
29/08/2024 11:29:35:738= Reset receiver/transceiver: 0D 00 00 00 00 00 00 00 00 00 00 00 00 00 HA code:0D00000000000000000000000000 ...

Hi

I have bought an RFX868 to get the data from an Ecowitt WS90 sensor.
This WS90 sensor hasin fact 7 different sensors included
* Temperature
* Humidity
* Rain
* Wind
* UV level
* Solar power
* Barometric pressure
The RFX868 protocol to use has been defined using the RFXmngr.exe program on windows ...

Thanks for your reply
I have used RFXmngr to configure the requiert mode of my RFX868. So I will check again if I can see the sensor data in Domoticz

Hi,

I am new to this forum but an old user of Domoticz
Using Domoticz for many years now I decided to add an RFX868XL module to get data from my Ecowitt WS90 sensor
The problem is that once connected to the raspberry pi running domoticz I cannot find the correct protocol in the domoticz ...