Followup with my setting with Shelly 1 or 1PM, Domoticz, Domoticz Bridge with Alexa skill and shelly MQTT..... in Ubuntu, I believe PI will be the same. I have everything configured and its working very well. In addition, I have IOS app Pilot also configured. Unix mqtt broker installation and ...

Thank you so much @besix. Now I get it. Can't set that button type, so I just have to forego that status. Got the domotize bridge working for Alexa after read and run tests with this: https://da-bridge.tarthorst.net/ I hate to open port 80 or 443 with my ddns for alexa. Nevertheless, its an eval I ...

OK, I found one of my problems, you cannot install both shelly mqtt and mqtt gateway in the hardware section of Domoticz. When I stopped the Mqtt gateway, the two devices have disappeared.
Nevertheless, I am still not able to update that mqtt device in Alexa via domoticz bridge.

This is the first time I install Shelly mqtt, please bear with me I installed shelly mqtt plugin and MQTT client gateway on my ubuntu server. Also, I set two hardware entries in Domoticz one for the shelly mqtt and another for MQTT client gateway. They are running. However Domoticz discovered three ...

Have been using Domoticz for years, first attempt to setup a scene (not groups) I have a dummy switch that is controlled by http commands from another app. It is working fine. how can I use this dummy switch as a Master to turn on/off some sonoff switches that is currently working in Domoticz as ...

I finally come up with a design idea On the poolside, use a battery-powered waterproof 433Mhz, Zigbee or Z-Wave transmitter combined with a float sensor to detect the water level. This can be bolted into the skimmer cover. I have tested a wired solution with a float sensor in the pool, but because ...

Thank you @waaren
I will try that

Thank you and to answer your question @waaren 1. By name of the switch do you mean the name of the virtual switch? Its called sonoff7 idx 13 its always off with a weekly on time 2. Time, will be weekly, Friday, at 17:00 on and off 15 min. Later or Saturday the same time if the Friday weather is too ...

I have a sonoff basic switch loaded with ESP Easy, which works fine using the timer in domoticz. My goal is trying to turn on the switch at a prescribed time only if certain weather conditions are met, such as if the wind is less than x Km/h and or temp is in a certain range (whatever it is in the ...

@zicht "Why not a floating sensor that makes a contact when below a certain level and then time the value needed." You are absolutley right. I have thought about it, however, you know the wall of an inground swimming pool is made of thick cement and tiles, in addition, it is surrounded by a cement ...

Thank you @waaren Each hardware I found on the market is proprietary Does anyone know if there are hardward available to work with Domoticz? I read a lot about irrigation controllers on this forum, so I have some idea about going forward. But has any one worked with water pressure gauges? Has anyone ...

I have a small project and don't know where it belongs. I want to install an inground swimming pool water auto-refill project. I have a pool and a pool filter system. The filer pump circulates the pool water through the filter to keep the pool clean. Since the water in the pool evaporates, the water ...

I am running the 2020.2 version of domoticz-most current and Ubuntu server 18.04LTS. In Domoticz I am able to retrieve snapshots from the Forscam camera(using the "cameras" setup) in Domoticz. In Ubuntu I am running "motion" in Ubuntu and are able to view images and clips in the /var/lib/motion ...

I think I know my problem. It has nothing to do with the plugins. It must have some thing to do with my Broadlink RM firmware. I have not been able to updated the firmware with an IOS device, I need an Android phone to make the update.

Thanks zak45 I just realized that this plugin must be running under domoticz 3.9 or higher, I am running 3.7. So I will try to update first. However, I got this update problem "404 not found", I am going to work that. Hi I am back on broadlink. I have re-compiled a fresh domoticz and re-loaded the ...

@waaren Ok. everything is working, including restore database and load domoticz on reboot. Thank you. I tried to issue commands for updater described in the wiki. I have few problems 1. there is no monit in /etc/init.d/, perhaps it is an outdated reference not used today? 2. if I goto ~/domoticz and ...

@waaren U are absolutely correct. After I copied what you indicated below, domoticz started without any problem and I don't think the log is necessary. I can't edit the domoticz.sh file in the /etc/init.d/ anyway. right now the sh file in dev-domoticz has added log commands, but I don't think it is ...

here you go domoticz.txt Can you please share the contents of /etc/init.d/domoticz.sh (between code tags please) I think a step should be added in the build instructions and that is to copy from /dev-domoticz to the directory you are going to use for ' production' You want to keep the production ...

Thanks @warren I followed the instruction in the wiki page to the letter and was able to "make" or build from source code, Except in the last section, the instruction "cd domoticz" does not work, because there was nothing in that subdirectory, the current directory is /dev-domoticz I was able to run ...

@waaren Thanks. I took your code and created another process (updaterelease1) But I got the same 404 not found from executing it. I don't think your code is any different from updaterelease I have in the current directory. see the screen output.. domoticz1.jpg Now it seems the auto update program is ...