Eddy,

Ok thanks

I will look into that

Greetings

Hi, flokkie, Strange that the developpers are not asking for logfiles etc. to investigate the issue. I've a strong feeling that Domoticz is loosing the connection with the USB zwave controller for one or the other reason. If the developpers are not asking for detailed information needed to ...

Hi, That's a typo Launching the command ls -l /dev/ttyUSB* I get the following: /dev/ttyUSB0 /dev/ttyUSB0 -> ttyUSB21 As specified in the udev rule. The reason of this symlink is when the board is restarted than the zwave controller can change from USB port therefore the symlink is needed. But ...

Hi Eddy, Thanks for your resonse Indeed I'm using a udev rule Launching the command ls -l /dev/ttyUSB* I get the following: /dev/ttyUSB0 /dev/ttyUSB0 -> ttyUSB0 The rule itself is as follows: The rule itself is called: 11-zwave_controller.rules and it contains the following rule: SUBSYSTEM=="tty ...

As a fall back to previous versions is not an option a sollution is needed for the current version. :? Until know no suggestions or additional question to try to solve this behaviour in the current Domoticz version. :roll: As said i'm willing to provide the necessary info (logs, etc.) for ...

Philchillbill,

Thanks for your reply.

Actually I'm looking to a previous stable version like the one where I didn't percieve the current issue. So I'm looking for version 3.8153 of July 30th 2017

Good idea to store earlier versions localy, Something I will do in the future as well.

Thanks

Is there someone out there to tell me how to install a previous version of Domoticz?

Thanks

This item is already added quite often and disappear after some days. :shock: :evil: Configuration: Hardware: Cubie board Zwave USB stick: Aeotec Z-Stick S2 Software: Armbian 5.73 Linux 9 Stretch (4.19.25-Sunxi Domotcz version 4.10717 build hash: b38b49e5 OZW USB Version:1.4-3335-g74e05982-dirty ...

When I removed the FGS213.xml from the directory domoticz/Config/fibaro and rebuild the zwcfg_0x******.xml file then the FGS-213 is working fine. Now I have to compare the original FGS213.xml with what is currently in zwcfg_0x******.xml to see what is causing the incompatibility.

No solution for this issue?

Can this be solved by controlling the device via json interface?

for those listening thanks for replying....

Thanks jvdz I've seen that page already however it's not clear how to integrate this into LUA. In the location domotics/scripts/lua there is also a file JSON.lua but also here It isn't clear how to manage the json commands. If I have already one example to control a simple switch it will already ...

Hi all, I've searching the forum for a while looking for an example of switching on/off a switch via json. The reason behind is that the switch can be controlled by the Domoticz general way as the dat send by Domoticz is the command to set dimmer values while the device is just a switch (FGS-213 ...

Supplier: FIBARO Website: https://www.fibaro.com Function: FIBARO Switch 2 is designed to be installed in standard wall switch boxes or anywhere else where it is necessary to control electric devices. FIBARO Switch 2 allows to control connected devices either via the Z-Wave+ network or via a switch ...

Somebody out there to explain how to get control over the fgs-213?

Many thanks

System configuration: Cubietruck with OS Debian GNU/Linux 8.10 (jessie) Domotics version 3.8153 Build Hash: 494fff7 In the Zwave setup the following is found concerning the FGS213 node id Name Description Manufacture id Type Last seen polling 029 (0x1d) Badkamer_Ventilator FIBARO System FGS213 ...

Hi,

MiWa4711

The issue appeared again on my system probably after the upgrade to version 3.8153. so problem isn't solved

Hi all,

I will try this out. When I have som results I will put it here

If there is other advice feel free to share
Thank

Thanks, Concerning the wakeup time I was assuming that the device was listening to commands from the controller when he sends the movement sensor status. By then the periodic measurements are active and then when movement sensor is giving no movements detected for a while the periodic measurements ...

Hi, I've a problem with a battery powered z-wave Multi sensor containing a movement, humidity, light (lux),.. sensors. As the device is battery powered the device will become aware every 2 hours. The movement sensor is working fine, from the moment movement is detected the sensor reports the status ...

Hi,

I didn't do any upgrade.
So I don't know how the issue has been solved.

I will mark the first post as solved.

Thanks for the support.