waaren wrote: Saturday 10 October 2020 20:21 Thx.
Until the device adapter is integrated in domoticz Beta you can use something like below. (see for the selector one of the previous posts)

it's working now thank you

waaren wrote: Saturday 10 October 2020 19:09 OK. Can you also try the same without level 0 ?
I don't have the real device myself so I can only partially check the commands. The device does react in the GUI

that works also

Ok back to the drawing board then... :D
can you check if
http://<domoticz ip:domoticz:port>/json.htm?type=command&param=switchlight&idx=<open haard id>&switchcmd=Run%20Up&level=0
Works ?


that works valve is opening and i have tried the other commands and that works also
/json.htm?type ...

Yes. The nValue is controlling the status of this deviceType.

I will have a look to implement a device-adapter in dzVents for this device and also to see if it can be made possible to change the icon but don't expect that soon. For now I prepared the attached dzVents script that will set the ...

Thx. I still have some issues replicating this devicetype on my test system. Please execute below identification script and send the logresult. (you can use PM if there is stuff inside you don't want to share in the public part of the forum.

this is off

2020-10-09 17:40:36.762 Status ...

Do someone know how I can send the right command for the valve?

Can you show the device as it is on the device tab and as it is on the switch tab?
How do you control the valve with the GUI? When you click on the light bulb then comes a popup with 7 options you can choose to operate the valve ...

i have the mertik heard controller and i can send commands with the domoticz ui
i can turn it on/ off and control the valve

with the dzvent i can only sent the on and off command
i have checkt that when i send a comand the value chance for 0 to 6 with each it function
i can

do somone now how i ...

i have a arduino mkr 1010 and want to make a automatic plant watering.
i can already send values to domoticz from my sensors.
but i want also to read the status from a selector switch to know in which mode to operate.
if i put a constant value the code works, but i don't get a new json string from ...

Ps=1 didn't work so I deleted everything and start from scratch and now everything is up and running

Verstuurd vanaf mijn SM-G920F met Tapatalk

Where can I send that I have tried in domoticz by the hardware page, and the esp-link and also otmonitor

Verstuurd vanaf mijn SM-G920F met Tapatalk

A few hours ago the otgw did work. but I must clean up the mess so I put out the plug. And when I was done in put the plug back but now the otgw doesn't work with domoticz. I got messages from the otgw but he doesn't update the info
https://uploads.tapatalk-cdn.com/20170408 ...

I have tried that but I set it back to VR=1.
and if look at data from the boiler I see nothing but the thermostat does send data

Verstuurd vanaf mijn SM-G920F met Tapatalk

the esp is working thanks for that.
but the thermostat is giving a error: aansluit fout
and the boiler is not working but i get the messages in domoticz
2017-01-10 21:36:24.239 OTGW: PR: BV
2017-01-10 21:36:24.242 (thermostaat) Temp (Control Setpoint)
2017-01-10 21:36:24.245 (thermostaat ...

it was the tx and the rx
but can i now chance the switch and reset esp ?

I have also a raspberry 3 with domoticz on it, but with debian and have esptool installed with pip
bet when put in the last code i get this
pi@raspberrypi:~/esp-link-v2.2.3 $ esptool.py --port /dev/ttyUSB0 --baud 460800 write_flash -fs 32m -ff 80m \
> 0x00000 boot_v1.5.bin 0x1000 user1.bin 0x3FE000 ...

I have the same esp8266mod but i didn't get it flasht with the esp-link software can you help me with that?

Verstuurd vanaf mijn SM-G920F met Tapatalk