Search found 10 matches

by Solventus
Wednesday 17 August 2016 16:16
Forum: Z-Wave
Topic: Fibaro Motion Sensor Unknown
Replies: 42
Views: 13990

Re: Fibaro Motion Sensor Unknown

The values are: parameter 6 value 30 parameter 22 value 30 parameter 24 value Tamper I think that motion sensor is the 00000C00 Sensor. I have a FGMS-001 V2/7 too. When I include it, the system show 4 devices: 00000x00 motion sensor 00000x28 tamper 0000x03 lux 0x01 Temperature The V2/7 version works ...
by Solventus
Wednesday 17 August 2016 12:29
Forum: Z-Wave
Topic: Fibaro Motion Sensor Unknown
Replies: 42
Views: 13990

Re: Fibaro Motion Sensor Unknown

what are the values I should insert in those parameters?
by Solventus
Wednesday 17 August 2016 10:58
Forum: Z-Wave
Topic: Fibaro Motion Sensor Unknown
Replies: 42
Views: 13990

Re: Fibaro Motion Sensor Unknown

Hello.
I try include FGMS-001 EU V3.2 how you says. It works fine. Now, my devices are how it show in the image attached.
I don't understand why the sensor 00000C00 is always on.
The motion sensor not works.
I Thanks for your help.
My level of English is not very good . I am sorry.
by Solventus
Tuesday 16 August 2016 12:13
Forum: Z-Wave
Topic: Fibaro Motion Sensor is activated alone
Replies: 6
Views: 1285

Re: Fibaro Motion Sensor is activated alone

Hello everybody.
I have a new problem with fgms-001 fibaro motion sensor.
I install a new raspberry + razberry. When I include a FGMS-001 (3 units) then it show the next image.
The ID 600-700-800 are the FGMS.
I don't know why the fgms are always on.
Thanks
by Solventus
Thursday 23 June 2016 18:25
Forum: Z-Wave
Topic: help with my new project
Replies: 2
Views: 507

Re: help with my new project

Thanks you.
What powered device is the best for my network? Could I use the fibaro dimmer? Do you know some devices for this?
by Solventus
Thursday 23 June 2016 12:42
Forum: Z-Wave
Topic: help with my new project
Replies: 2
Views: 507

help with my new project

Hello everybody. I would like to make a new project to know where is my son when he is alone at home. For that, I have a few fibaro motion sensor and a door open sensor. My controler is RPI + Razberry and I'm working with Domoticz. I have a fibaro motion senson in each room. When I include the ...
by Solventus
Thursday 09 June 2016 12:45
Forum: Z-Wave
Topic: Fibaro Motion Sensor is activated alone
Replies: 6
Views: 1285

Re: Fibaro Motion Sensor is activated alone

Hello StandHD, all good now.
Thanks a lot for your help.
by Solventus
Tuesday 07 June 2016 12:53
Forum: Raspberry Pi GPIO ( WiringPi )
Topic: Razberry + Raspberry GPIO port
Replies: 2
Views: 3866

Razberry + Raspberry GPIO port

Hello, I have a Raspberry with a Razberry card.
Can I use the free GPIO pins?
I want to include a swich and to know its state.

Thanks a lot.
by Solventus
Thursday 02 June 2016 10:39
Forum: Z-Wave
Topic: Fibaro Motion Sensor is activated alone
Replies: 6
Views: 1285

Re: Fibaro Motion Sensor is activated alone

Hello StandHD, thanks a lot for your reply.
About sensitivity, Are you referring to parameter 1?
In this parameter I have a value of 10. What value do you have?
I haven't any intermittent heat source, but at night the temperature might be higher than during the day. Could that be a problem?
by Solventus
Wednesday 01 June 2016 16:52
Forum: Z-Wave
Topic: Fibaro Motion Sensor is activated alone
Replies: 6
Views: 1285

Fibaro Motion Sensor is activated alone

Hello, I have a Fibaro Motion Sensor in Domoticz.
At night, when there is nobody in the office the sensor is activated. I don't know why this happens.
Can you help me with that?

Thanks a lot.