Domoticz

Hi guys

does someone managed to have the ECR-100 module working with domoticz ?

here is the link

http://www.home-confort.net/fr/content/ ... -chauffage

I tried different signals but i don't know if i'm doing it well.

thank you in advance for your help

Looks exactly the same as: http://www.klikaanklikuit.nl/shop/nl/in ... -acm-1000/
Use type 'AC', use random code and when unit is in paring mode, click 'Test' button in Domoticz.



Let me know if it works

Thanks

it looks but it's not exactly the same, mine as a green led and seems to refuse to work with AC

I will try again this evening and keep you posted, could be usefull to know.

ThinkPad wrote:Looks exactly the same as: http://www.klikaanklikuit.nl/shop/nl/in ... -acm-1000/
Use type 'AC', use random code and when unit is in paring mode, click 'Test' button in Domoticz.

Let me know if it works

I doubt it is the same.
The RFLink Gateway supports the Home Confort Smart Home products (among others the TEL-010 remote control) and the protocol is totally different.

i tried by it dosen't work ...

I've been in contact with the RFXCOM team to implement this protocol on the RFXCOM module.

I just tested it with RFXMGR and it works perfectly i'm able to control these new modules

so now just nee to be implemented in Domoticz.

I posted a modification request in the tracker.

et me know if you need any help to test it.

cheers

sebastien

more info on HOME COMFORT modules : http://www.home-confort.net

they are exactly the same than chacon but cheaper (got one for 10€)

Need this to !

here the request in the tracker

http://www.domoticz.com/forum/tracker.php?p=2&t=615

the protocol is already available in the last RFXCOM firmware but need to be avilable on Domoticz;

Hello

I have several ecr-100 Module

I can not operate with a domotickz and rxfcom433E Version 248.

help thank you

Did you try with RFXmngr?

I suppose HomeConfort is not yet implemented in Domoticz, see http://www.domoticz.com/forum/tracker.php?p=2&t=615

Hello

I just tested RFXmngr.

The selection I HC tab.
and selection of telecommandeTEL-010 (the remote control supplied with the ECR-100 module is the TEL-010 model)

I try a aperage but nothing happens.

I was therefore unable to operate the ECR-module 100 ave key RFXcom433E ....

Use an RFXtrx433E with firmware version 248.
Connect RFXmngr and enable only the HomeConfort protocol,
Transmit a command using the TEL-010 remote.
Check the codes received and transmit a command with RFXmngr using the same codes as received from the TEL-010.

It's ok

================================================
Home Confort command
================================================
Packettype = Home Confort
subtype = TEL-010
Sequence nbr = 6
ID = 1010C decimal:65804
House Code = A
Unit Code = 1
Command = On
Signal level = 0 -120dBi
------------------------------------------------
Packettype = Receiver/Transmitter Message
subtype = Transmitter Response
Sequence nbr = 6
response = ACK, data correct transmitted
================================================
Home Confort command
================================================
Packettype = Home Confort
subtype = TEL-010
Sequence nbr = 7
ID = 1010C decimal:65804
House Code = A
Unit Code = 1
Command = Off
Signal level = 0 -120dBi
------------------------------------------------
Packettype = Receiver/Transmitter Message
subtype = Transmitter Response
Sequence nbr = 7
response = ACK, data correct transmitted

Merci Thank's :p

Ok, HOME COMFORT modules are know seen under RFXmgr, but not by DOMOTICZ

Best regards

Implemented in #3524, hope it works well

Nice job it's ok For me .

Great! thanks for the feedback

bakc from business trip I will try it soon and post a feedback

thank you gizmo !!

S.

gizmocuz wrote:Implemented in #3524, hope it works well

Hi gizmocuz,

Imposible to check "home confort" box in hardware set mode !

The system refuse this choice !

it's the same think with usb rfxcom 433 and usb rfxcom 433 E

Do you have an idea ?

Bests regards