Page 1 of 1

rflink sends signal but domoticz does not update (EV1527)

Posted: Tuesday 14 July 2020 21:02
by emichiels
Hi all,

Yesterday I received some doorsensors and started to integrate them in my domoticz system. These are EV1527 devices,sending 433mhz signal. Rflink recognized them as soon as they were used and within domoticz 2 devices were created automaticly (one for open one for close). the last time used was updated.

After that when I use the sensor (open or close the door) nothing happens in Domoticz. I started investigating and found out the data of the device is coming in on the serial port of the Rflink device.

Code: Select all

20;20;EV1527;ID=XXXXXX;SWITCH=03;CMD=ON;
Also I have debugged it with rflinkloader.

Code: Select all

20;1C;EV1527;ID=xxxxxx;SWITCH=03;CMD=ON;
20;1D;DEBUG;Pulses=50;Pulses(uSec)=390,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1140,300,1140,300,300,1140,1110,300,1110,300,1110,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1110,300,1140,330,300,6990;
20;1E;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1140,300,1140,330,300,6990;
20;1F;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1140,300,1110,300,1110,300,1140,300,300,1140,1140,300,1110,300,1140,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1110,300,1110,330,300,6990;
20;20;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1140,300,300,1140,1140,300,1140,300,1140,300,300,1140,300,1140,300,1140,300,1140,300,1110,300,1140,300,1140,300,1140,300,1140,1140,300,1140,330,300,6990;
20;21;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1140,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1140,300,300,1140,1110,300,1140,300,1110,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1140,300,1140,330,300,6990;
20;22;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1110,300,1140,300,1140,300,1140,1110,300,1110,330,300,6990;
20;23;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1140,300,300,1140,1110,300,1140,300,1140,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1110,300,1140,300,1140,300,1140,1110,300,1140,300,300,6990;
20;24;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1140,300,1110,300,300,1140,1140,300,1140,300,1140,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1110,300,1140,330,300,6990;
20;25;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1140,300,300,1140,1110,300,1110,300,1110,300,1140,300,300,1140,1140,300,1140,300,1140,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1140,300,1140,330,300,6990;
20;26;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1140,300,1110,300,1140,300,300,1140,1140,300,1140,300,1110,300,1140,300,300,1140,1140,300,1140,300,1140,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1140,300,1140,330,300,6990;
20;27;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1140,300,1110,300,300,1140,1110,300,1140,300,1110,300,1140,300,300,1140,1110,300,1140,300,1140,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1110,300,1140,330,300,6990;
20;28;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1140,300,1110,300,300,1140,1140,300,1140,300,1140,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1140,300,1140,330,300,6990;
20;29;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1140,300,300,1140,1110,300,1110,300,1110,300,1140,300,300,1140,1140,300,1110,300,1140,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1140,300,1110,330,300,6990;
20;2A;DEBUG;Pulses=48;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1140,300,1110,300,1140,300,300,1140,1140,300,1140,300,1140,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1140,300,1140,6990;
20;2B;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1140,300,1140,300,300,1140,1140,300,1140,300,1140,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1140,300,300,1140,300,1140,1110,330,300,6990;
20;2C;EV1527;ID=xxxxxx;SWITCH=09;CMD=ON;
20;2D;DEBUG;Pulses=50;Pulses(uSec)=390,1140,1110,300,1140,300,1140,300,300,1140,1110,300,1110,300,1140,300,1140,300,300,1140,1110,300,1110,300,1140,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1140,300,300,1140,300,1140,1110,330,300,6990;
20;2E;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1140,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1110,300,300,1140,1140,300,1140,300,1140,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1110,300,300,1140,300,1140,1140,330,300,6990;
20;2F;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1140,300,300,1140,1140,300,1110,300,1110,300,300,1110,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1140,300,300,1140,300,1140,1110,330,300,6990;
20;30;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,300,1110,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1140,300,300,1140,300,1140,1110,330,300,6990;
20;31;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1110,300,300,1140,1110,300,1140,300,1110,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1110,300,300,1140,300,1140,1140,330,300,6990;
20;32;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1140,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1110,300,1140,1110,300,300,1140,300,1140,1140,300,300,6990;
20;33;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1110,300,1140,1110,300,300,1140,300,1140,1110,330,300,6990;
20;34;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,300,1140,300,1140,300,1140,300,1110,300,1140,300,1140,300,1140,1110,300,300,1140,300,1140,1140,330,300,6990;
20;35;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1140,300,300,1140,300,1140,300,1140,300,1110,300,1140,300,1140,300,1140,1110,300,300,1140,300,1140,1110,330,300,6990;
20;36;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1110,300,300,1110,1140,300,1110,300,1110,300,300,1140,300,1140,300,1140,300,1110,300,1140,300,1140,300,1140,1110,300,300,1140,300,1140,1110,330,300,6990;
20;37;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1140,300,300,1140,1110,300,1140,300,1110,300,300,1140,300,1110,300,1140,300,1140,300,1140,300,1140,300,1110,1140,300,300,1140,300,1140,1140,330,300,6990;
20;38;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,300,1140,300,1110,300,1140,300,1140,300,1140,300,1140,300,1140,1110,300,300,1110,300,1140,1110,330,300,6990;
20;39;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1110,300,300,1110,1110,300,1110,300,1110,300,300,1140,300,1110,300,1140,300,1110,300,1140,300,1140,300,1140,1110,300,300,1110,300,1140,1110,330,300,6990;
20;3A;DEBUG;Pulses=48;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1110,300,300,1110,300,1140,1140,6990;
20;3B;DEBUG;Pulses=30;Pulses(uSec)=1170,300,1140,300,1140,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1110,300,1110,330,300,6990;
20;3C;DEBUG;Pulses=34;Pulses(uSec)=450,300,270,1080,1080,270,1080,270,1080,270,270,1080,270,1110,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1140,300,1140,330,300,6990;
20;3D;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1140,300,1140,300,1110,300,1140,300,300,1140,1140,300,1140,300,1140,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1140,300,1110,330,300,6990;
20;3E;EV1527;ID=xxxxxx;SWITCH=03;CMD=ON;
20;3F;DEBUG;Pulses=50;Pulses(uSec)=390,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1140,300,300,1140,1110,300,1110,300,1110,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1110,300,1110,330,300,6990;
20;40;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1140,300,300,1140,1140,300,1110,300,1140,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1140,300,1110,330,300,6990;
20;41;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,300,1140,300,1140,300,1140,300,1140,300,1110,300,1140,300,1140,300,1140,300,1140,1110,300,1110,330,300,6990;
20;42;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1110,300,1110,330,300,6990;
20;43;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1110,300,300,1140,1110,300,1140,300,1140,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1140,300,1110,330,300,6990;
20;44;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1140,300,300,1140,1140,300,1110,300,1110,300,300,1110,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1110,300,1140,1110,300,1140,330,300,6990;
20;45;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,300,1110,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1110,300,1140,1110,300,1110,330,300,6990;
20;46;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1110,300,300,1140,1140,300,1110,300,1110,300,300,1110,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1110,300,1110,330,300,6990;
20;47;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,300,1110,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1140,300,1110,330,300,6990;
20;48;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1140,300,300,1140,1110,300,1140,300,1140,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1110,300,1140,330,300,6990;
20;49;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1110,300,300,1140,1140,300,1140,300,1140,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1140,300,1140,330,300,6990;
20;4A;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1140,300,1110,300,300,1140,1140,300,1110,300,1110,300,1140,300,300,1140,1140,300,1110,300,1140,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1140,300,1110,330,300,6990;
20;4B;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1140,300,300,1140,1110,300,1110,300,1110,300,1110,300,300,1140,1140,300,1140,300,1140,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1110,300,300,1140,300,1140,1140,330,300,6990;
20;4C;EV1527;ID=xxxxxx;SWITCH=09;CMD=ON;
20;4D;DEBUG;Pulses=50;Pulses(uSec)=390,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1110,300,300,1140,1110,300,1140,300,1110,300,300,1110,300,1140,300,1140,300,1140,300,1140,300,1110,300,1140,1110,300,300,1140,300,1140,1110,330,300,6990;
20;4E;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1140,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1110,300,300,1140,300,1140,1110,330,300,6990;
20;4F;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1110,300,300,1140,1110,300,1140,300,1110,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1110,300,1140,1110,300,300,1140,300,1140,1140,300,300,6990;
20;50;DEBUG;Pulses=50;Pulses(uSec)=390,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1110,300,300,1110,1140,300,1140,300,1110,300,300,1140,300,1140,300,1140,300,1110,300,1140,300,1140,300,1140,1110,300,300,1140,300,1140,1110,330,300,6990;
20;51;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1110,300,300,1140,1110,300,1140,300,1110,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1110,300,300,1140,300,1140,1140,330,300,6990;
20;52;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1110,300,300,1140,1140,300,1140,300,1140,300,300,1140,300,1110,300,1140,300,1140,300,1140,300,1140,300,1140,1110,300,300,1110,300,1140,1110,330,300,6990;
20;53;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1140,300,1140,300,300,1140,1140,300,1110,300,1140,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1140,300,300,1140,300,1140,1110,330,300,6990;
20;54;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1140,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1140,300,300,1140,1140,300,1140,300,1140,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1140,300,300,1140,300,1110,1140,330,300,6990;
20;55;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1140,300,300,1140,1110,300,1110,300,1110,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1140,300,300,1140,300,1140,1140,330,300,6990;
20;56;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1140,300,300,1140,1140,300,1110,300,1110,300,1110,300,300,1140,1140,300,1140,300,1140,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1110,300,300,1140,300,1140,1140,330,300,6990;
20;57;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1140,300,300,1140,1110,300,1110,300,1110,300,1140,300,300,1140,1110,300,1110,300,1140,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1140,300,300,1140,300,1140,1110,330,300,6990;
20;58;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1140,300,1110,300,1110,300,300,1140,1140,300,1110,300,1110,300,1140,300,300,1140,1140,300,1140,300,1110,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1110,300,300,1140,300,1140,1110,330,300,6990;
20;59;DEBUG;Pulses=50;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1140,300,300,1140,1140,300,1140,300,1110,300,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,300,1140,1110,300,300,1140,300,1140,1110,330,300,6990;
20;5A;DEBUG;Pulses=48;Pulses(uSec)=360,1140,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,1110,300,300,1140,1110,300,1110,300,1110,300,300,1110,300,1140,300,1140,300,1140,300,1140,300,1110,300,1140,1110,300,300,1140,300,1140,1110,6990;
So according to me Rflink is working just fine.

Anybody an idea how to solve this?

Re: rflink sends signal but domoticz does not update (EV1527)

Posted: Saturday 25 July 2020 10:24
by sancla
Could it be a power issue?

Re: rflink sends signal but domoticz does not update (EV1527)

Posted: Wednesday 25 November 2020 17:51
by emichiels
I don't know what it was. But after a couple of days. I have never found the cause of the earlier problem. But for me the problem is solved now

Re: rflink sends signal but domoticz does not update (EV1527)

Posted: Sunday 10 January 2021 13:10
by DarenFord
Hi,

I had a similar problem with Kerui door/window (D026) and motion sensors in combination with RF Link.

These sensors created devices and seemed to work, but a day later they stopped working and had created a bunch of new devices in Domoticz.

The new devices worked for a while, but after restarting the RF Link gateway it seemed to revert back to the original devices which was quite frustrating. Other forum posters were reporting a similar problem. I had also had some trouble in the past with remote control modules which used the EV1527 protocol (of the 4 button inputs, Domoticz only seemed to register the first button input as a device), so it looked like RF Link wasn't supporting the EV1527 protocol very reliably.

In the end, I created a gateway specifically for EV1527, using the RF Link serial protocol to connect to Domoticz, to properly support these devices. I've made this available (open source) for anyone else who wants to go down the same route.

https://github.com/DarenFord/EV1527Link

Hope this helps,
Daren.