Domoticz

Posted: **Saturday 27 October 2018 11:20**

Hello,

I am unable to SetMode in rfxcom pannel: I return to Dashboard and all devices stay to red (disable).

Here is my log file:

Code: Select all

 2018-10-27 10:22:16.378 Status: RFXCOM: Using serial port: /dev/ttyUSB1
2018-10-27 10:24:31.684 Error: RFXCOM: Invalid data received!....
2018-10-27 10:24:35.609 subtype = Interface Command
2018-10-27 10:24:35.609 Sequence nbr = 3
2018-10-27 10:24:35.609 set configuration of the interface

domoticz v4.9700 on raspberry Raspbian Stretch Lite
RFXtrx433XL update to the last firmware: RFXtrx433XL_ProXL1_1031.hex

Here is what I tried:

I tried to restart domoticz (stop/unplug/restart)
Hardware is enable
RFXtrx433XL is on /dev/ttyUSB1
Zigate is on /dev/ttyUSB0
I have version 0
I have read the post: RFXtrx433 Version 0
I have a RFXtrx433E on another raspberry and manualy copy the same config
RFXtrx433XL can update firmwae
RFXtrx433XL can detect oregon THGR810 with the RFXmngr software on W10

Thank you

Regards

Posted: **Sunday 28 October 2018 9:10**

Does somebody was able to successfully use the new RFXtrx433XL with domoticz stable 4.9700?

Posted: **Sunday 28 October 2018 9:59**

Yep i do, without any problem.

I only use the latest beta....

Posted: **Sunday 28 October 2018 11:15**

Thank you antwan.
Did you test with the stable before beta?
What beta version number is OK?

Posted: **Sunday 28 October 2018 20:32**

Im always on the beta channel, and i never look back.

Posted: **Monday 26 November 2018 18:42**

Hello,
I have been able to use it on the stable version during 2 weeks,
now i have only the following:

2018-11-26 17:28:55.928 Error: RFXCOM: input buffer out of sync, going to restart!....

2018-11-26 18:34:38.003 Error: RFXCOM: Invalid data received!....

it seems fine on RFXmngr,
I have updated to the 1032 firmware, no difference.

Posted: **Monday 26 November 2018 19:23**

i have reboot the pi,
deleted the RFXCOM hardware, created a new one (and changed the usb port) something happened at the usb management
now it is fine.

Posted: **Monday 04 May 2020 18:26**

I had the same problem: Domoticz was not saving any changes I made to the RFXCOM-protocols and all were disabled. I removed the RFXCOM and added it with a different USB-port. Now when I click Set Mode I'll see some protocols enabled and I'm able to toggle all. Clicking on the red button Set Mode saves the changes (somewhat unintuitive; 'Save' would be better IMHO). So this solved my problem.

Domoticz

RFXtrx433XL : invalid data received - version 0

RFXtrx433XL : invalid data received - version 0

Re: RFXtrx433XL : invalid data received - version 0

RFXtrx433XL : invalid data received - version 0

Re: RFXtrx433XL : invalid data received - version 0

Re: RFXtrx433XL : invalid data received - version 0

Re: RFXtrx433XL : invalid data received - version 0

Re: RFXtrx433XL : invalid data received - version 0

Re: RFXtrx433XL : invalid data received - version 0