Domoticz

You could take a look here
viewtopic.php?f=50&t=9362#p97362
Same type of "only On" challenge,
but Blockly is triggered by a new On pulse.

Thx... but I don't understand anything off it. BlocklY is not my kind of doing things.

Is there someone who can make a LUA-script for this problem?

I have mulitple ON-pulses (everytime I push the button). So I need a dummy which goes on on the button ON-pulse, and switches back to OFF after 5 seconds (or something like that)
So I can use the dummy-switch (which does have ON and OFF state) for switching other devices.

(command like devicechanged will not work)

Melissen wrote:Thx... but I don't understand anything off it. BlocklY is not my kind of doing things.

Is there someone who can make a LUA-script for this problem?

I have mulitple ON-pulses (everytime I push the button). So I need a dummy which goes on on the button ON-pulse, and switches back to OFF after 5 seconds (or something like that)
So I can use the dummy-switch (which does have ON and OFF state) for switching other devices.

(command like devicechanged will not work)

You could put a JSON command in the virtual switch's on action, to turn itself off after some delay.

I fixed it.... made a very simple script. Only use DeviceChanged function but not with an On/Off state selection and the end of this command.

for example:
If devicechanged['doorbell'] then
Instead of:
If devicechanged['doorbell']="On" then

thecosmicgate wrote:

I followed this guide, but the thing i want or need is just to separate the chime button from the chime .
So these 2 are two different devices . so i can use a blockly and timer when the chime doesn´t make any sound etc.
I tried everything without succes , is there anybody who can help me ?
( or is the only solution to buy a second action / selectplus doorbel ? )

did you( someone ) figure out how to do this?

Thomasdc wrote:

thecosmicgate wrote:

I followed this guide, but the thing i want or need is just to separate the chime button from the chime .
So these 2 are two different devices . so i can use a blockly and timer when the chime doesn´t make any sound etc.
I tried everything without succes , is there anybody who can help me ?
( or is the only solution to buy a second action / selectplus doorbel ? )

did you( someone ) figure out how to do this?

After a lot of failure this was working for one or 2 days , then it stops .
So nowadays I changed to a complete different solution using z-wave

Still interested too !!!!

I use the button to switch on and off my lights, but indeed would like the chime separately to notify an event in my livingroom.....

My Code :

Somebody tried the Linbell (Self Powered Wireless Doorbell) doorbell already with Domoticz?

Has anyone added this specific cheap doorbell to their setup?
It would be great if it's compatible, otherwise I'll have to invest in a new one.

Anyone got the (additional) bell push Byron BY37 working?

It operates aso on 433.92MHz, I tried the undec and Byron SX protocol, but it isn't seen by my Domoticz. Using the latest firmware (1025) for the RFXcom.

The reason I tried it was because it's IP44. I already used a few bell push devices, but one after the other dies (oxidised mostly).....

Edit:

I've sent the data the RFXmgr received to RFXcom. The sad thing was....the battery supplied with the bell push, was empty. With a new battery, I was able to receive messages. Hopefully they can add the bell push to a new firmware for the RFXcom.

Edit II:

The Byron BY37 now works in combination with the RFXcom with the latest beta firmware I received from them. Many thanks to Bert .

I just bought a Honeywell/Novar DC845 doorbell. The package says it is 434MHz, so I figured adding through my RFXCOM would be simple. No such thing. Does anyone have luck/experience with this device?

Link: https://goo.gl/chr2oK