SolarEdge via LAN interface

[rogerthn]

No luck
@freijn You did say

I do not have computed but from device

What Sensor Type is your device SolarEdge Power Kwh

I do have Sensor Type Electric (Instant+Counter) and with from device the update command needs to be an other than below?
urlmessage = 'http://'+domoip+':'+domoport+'/json.htm?type=command&param=udevice&idx='+str(domoidx)+'&svalue='+str(domovalue)

[freijn]

Capture.JPG (16.21 KiB) Viewed 1289 times

Capture.JPG (16.21 KiB) Viewed 1289 times

let me check the url

[rogerthn]

Running update every 10 second now and so far there seems to be a difference.

Unlike me you do have SolarEdge_Modbus Hardware i.e. I've missed to add Hardware
Can you share yours including settings?

2020-02-25 080009.jpg (7.16 KiB) Viewed 1278 times

[freijn]

Running update every 10 second now and so far there seems to be a difference.

Unlike me you do have SolarEdge_Modbus Hardware i.e. I've missed to add Hardware
Can you share yours including settings?
2020-02-25 080009.jpg

Roger,

I have no clue what you are asking now Can you please help me to understand which include settings you are looking for?

b.t.w. Are you running the Perl code or the Python code?

[rogerthn]

Roger,

I have no clue what you are asking now Can you please help me to understand which include settings you are looking for?

b.t.w. Are you running the Perl code or the Python code?

Never mind
I am running the Perl code and the only minor issue is the diff on daily production compared with SolarEdge monitoring.

[Hagen]

Hej there,

I'm a newbie to domoticz and scripting - but i finally got the perl script working on my rasperry connected to a SolardEdge Se7k by modbus TCP. Actually, there is only one problem: How can I get the real power value (describing in/out of power to the grid) or alternatively incoming and outgoing grid power into the script and finally into domoticz?

Regards

Hagen

[MeAlbert]

I found sunspec_ardexa


It ia a python script and is working much faster then the pearl script


https://pypi.org/project/sunspec-ardexa/

And you dont need to install much librarys for it

$ sunspec_ardexa discover 192.168.102.41 1

Output is

Name: common Sunspec Id: 1 Label: Common
Manufacturer (Mn) SolarEdge
Model (Md) SE4000
Version (Vr) 0003.2221
Serial Number (SN) 73133F27
Device Address (DA) 1

Name: inverter Sunspec Id: 101 Label: Inverter (Single Phase)
Amps (A) 1.74 A
Amps PhaseA (AphA) 1.74 A
Phase Voltage AB (PPVphAB) 236.0 V
Watts (W) 383.1 W
Hz (Hz) 50.02 Hz
VA (VA) 412.5 VA
VAr (VAr) 152.88 var
PF (PF) 92.87 Pct
WattHours (WH) 9371992 Wh
DC Amps (DCA) 1.0329 A
DC Voltage (DCV) 376.5 V
DC Watts (DCW) 388.9 W
Heat Sink Temperature (TmpSnk) 41.79 C
Operating State (St) MPPT
Vendor Operating State (StVnd) 0
Vendor Event Bitfield 1 (EvtVnd1) 1
Vendor Event Bitfield 4 (EvtVnd4) 0

I can install it on my Pi where also Domoticz is running on that's no problem but it is not clear to me how to get it in Domoticz.

[Piacco]

I can install it on my Pi where also Domoticz is running on that's no problem but it is not clear to me how to get it in Domoticz.

There's a description on this post
viewtopic.php?f=65&t=31455