[ESP8266] Commercial H801 WiFi RGB-dimmer topic
Moderator: leecollings
- ledfreak3d
- Posts: 98
- Joined: Sunday 01 November 2015 15:30
- Target OS: Linux
- Domoticz version: 3.8025
- Location: Hoorn
- Contact:
Re: [ESP8266] Commercial H801 WiFi RGB-dimmer topic
Hi you mean the rgbw plugin yes i can make you a bin file but you can also just compile it in the arduino ide
Unleashe the magic smoke ;)
-
- Posts: 784
- Joined: Wednesday 10 December 2014 13:06
- Target OS: Linux
- Domoticz version: beta
- Location: Bordeaux France
- Contact:
Re: [ESP8266] Commercial H801 WiFi RGB-dimmer topic
Even wolph made a script to use it with original fw to !
Easy to set, fast to drive solution.
Easy to set, fast to drive solution.
Domoticz stable 3.5877 for real & Domoticz beta for test
Rfxtrxe / RFLink / Milight / Yeelight / Tasmota / MQTT / BLE / Zigate
http://domo-attitude.fr
Rfxtrxe / RFLink / Milight / Yeelight / Tasmota / MQTT / BLE / Zigate
http://domo-attitude.fr
-
- Posts: 13
- Joined: Wednesday 03 August 2016 8:25
- Target OS: Raspberry Pi / ODroid
- Domoticz version: 3.4834
- Location: Netherlands
- Contact:
Re: [ESP8266] Commercial H801 WiFi RGB-dimmer topic
Somehow, I am not able to flash it via an Arduino...
I keep getting the following error...
warning: espcomm_sync failed
error: espcomm_open failed
error: espcomm_upload_mem failed
error: espcomm_upload_mem failed
According to the leds, it trys to do something, but I get the error...
Any tips?
I keep getting the following error...
warning: espcomm_sync failed
error: espcomm_open failed
error: espcomm_upload_mem failed
error: espcomm_upload_mem failed
According to the leds, it trys to do something, but I get the error...
Any tips?
- wolph
- Posts: 16
- Joined: Sunday 13 September 2015 16:12
- Target OS: Raspberry Pi / ODroid
- Domoticz version:
- Contact:
Re: [ESP8266] Commercial H801 WiFi RGB-dimmer topic
Try lowering the baud rate, whenever I get that error it's usually due to a baud rate that's too high or not enough power to the chip.
-
- Posts: 13
- Joined: Wednesday 03 August 2016 8:25
- Target OS: Raspberry Pi / ODroid
- Domoticz version: 3.4834
- Location: Netherlands
- Contact:
Re: [ESP8266] Commercial H801 WiFi RGB-dimmer topic
Unfortunately that does not change anything...
Even with 12v connected to the normal ports, no change...
I leave J3 connected... connected tx > rx and vice versa.. still no luck
Even with 12v connected to the normal ports, no change...
I leave J3 connected... connected tx > rx and vice versa.. still no luck
-
- Posts: 25
- Joined: Thursday 13 October 2016 21:45
- Target OS: Raspberry Pi / ODroid
- Domoticz version: Stable
- Location: Kent, England
- Contact:
Re: [ESP8266] Commercial H801 WiFi RGB-dimmer topic
Hi
My H801 has TX & RX transposed so I need to connect TX to TX and RX to RX. Do you get any out our on the serial monitor when you reset the device without the flash jumper shorted?
My H801 has TX & RX transposed so I need to connect TX to TX and RX to RX. Do you get any out our on the serial monitor when you reset the device without the flash jumper shorted?
-
- Posts: 13
- Joined: Wednesday 03 August 2016 8:25
- Target OS: Raspberry Pi / ODroid
- Domoticz version: 3.4834
- Location: Netherlands
- Contact:
Re: [ESP8266] Commercial H801 WiFi RGB-dimmer topic
I have tried it again today with a Linux (Debian) machine.. exactly the same error...
I have tried several baud settings...
I have played with the tx/rx wires
I am lost... :p
Now waiting for a USB/FTDI adapter... maybe that will help..
I have tried several baud settings...
I have played with the tx/rx wires
I am lost... :p
Now waiting for a USB/FTDI adapter... maybe that will help..
- ledfreak3d
- Posts: 98
- Joined: Sunday 01 November 2015 15:30
- Target OS: Linux
- Domoticz version: 3.8025
- Location: Hoorn
- Contact:
Re: [ESP8266] Commercial H801 WiFi RGB-dimmer topic
flashing the h801 is not a big problem
but cant get the white side to work
does it need something to be modified ?
rgb works great
but cant get the white side to work
does it need something to be modified ?
rgb works great
Unleashe the magic smoke ;)
-
- Posts: 25
- Joined: Thursday 13 October 2016 21:45
- Target OS: Raspberry Pi / ODroid
- Domoticz version: Stable
- Location: Kent, England
- Contact:
Re: [ESP8266] Commercial H801 WiFi RGB-dimmer topic
Hi ledfreak3d
Which port on the H801 are you using? Mine works fine on W2.
Which port on the H801 are you using? Mine works fine on W2.
- ledfreak3d
- Posts: 98
- Joined: Sunday 01 November 2015 15:30
- Target OS: Linux
- Domoticz version: 3.8025
- Location: Hoorn
- Contact:
Re: [ESP8266] Commercial H801 WiFi RGB-dimmer topic
have leds connected to all ports but for some reason white never works tried mapping it to other pins but same problem
is there a change needed to a script to get the milight plugin working correctly ?
rgb works fine
is there a change needed to a script to get the milight plugin working correctly ?
rgb works fine
Unleashe the magic smoke ;)
-
- Posts: 13
- Joined: Wednesday 03 August 2016 8:25
- Target OS: Raspberry Pi / ODroid
- Domoticz version: 3.4834
- Location: Netherlands
- Contact:
Re: [ESP8266] Commercial H801 WiFi RGB-dimmer topic
ledfreak3d, how did you flash it?
- ledfreak3d
- Posts: 98
- Joined: Sunday 01 November 2015 15:30
- Target OS: Linux
- Domoticz version: 3.8025
- Location: Hoorn
- Contact:
Re: [ESP8266] Commercial H801 WiFi RGB-dimmer topic
the normal way arduino ide
that's the only way you can get the milight plugin in there
plugin works fine rgb is working but none of the white are
that's the only way you can get the milight plugin in there
plugin works fine rgb is working but none of the white are
Unleashe the magic smoke ;)
-
- Posts: 25
- Joined: Thursday 13 October 2016 21:45
- Target OS: Raspberry Pi / ODroid
- Domoticz version: Stable
- Location: Kent, England
- Contact:
Re: [ESP8266] Commercial H801 WiFi RGB-dimmer topic
ledfreak3d - just checked mine with Domoticz and the same as you, white doesn't work. I'd only previously used it by sending this ..
http://192.168.1.92/control?cmd=PWMFADE,3,500,5 - which lights the strip white, attached to W2
Not sure what to do in Domoticz though, RGB on the wheel works fine.
http://192.168.1.92/control?cmd=PWMFADE,3,500,5 - which lights the strip white, attached to W2
Not sure what to do in Domoticz though, RGB on the wheel works fine.
-
- Posts: 1601
- Joined: Friday 18 October 2013 23:33
- Target OS: Raspberry Pi / ODroid
- Domoticz version: BETA
- Location: Arnhem/Nijmegen Nederland
- Contact:
Re: [ESP8266] Commercial H801 WiFi RGB-dimmer topic
mmm Orded a H801...
Perhaps someone have a good how to?
Youtube or something else?
Or are there perhaps other boards that can control RGBW strips?
Perhaps someone have a good how to?
Youtube or something else?
Or are there perhaps other boards that can control RGBW strips?
Xu4: Beta Extreme antenna RFXcomE,WU Fi Ping ip P1 Gen5 PVOutput Harmony HUE SolarmanPv OTG Winddelen Alive ESP Buienradar MySensors WOL Winddelen counting RPi: Beta SMAspot RFlinkTest Domoticz ...Different backups
- ledfreak3d
- Posts: 98
- Joined: Sunday 01 November 2015 15:30
- Target OS: Linux
- Domoticz version: 3.8025
- Location: Hoorn
- Contact:
Re: [ESP8266] Commercial H801 WiFi RGB-dimmer topic
the h801 works pretty good for all sorts of things and its cheap
the only weird thing with the h801 is that the programming ports it not connected to serial 0
one of the lines I think its rx but not 100% sure is connected to serial 1
so ive modded mine
else in some cases it wont talk back after programming
the only weird thing with the h801 is that the programming ports it not connected to serial 0
one of the lines I think its rx but not 100% sure is connected to serial 1
so ive modded mine
else in some cases it wont talk back after programming
Unleashe the magic smoke ;)
-
- Posts: 784
- Joined: Wednesday 10 December 2014 13:06
- Target OS: Linux
- Domoticz version: beta
- Location: Bordeaux France
- Contact:
Re: [ESP8266] Commercial H801 WiFi RGB-dimmer topic
below my way to drive W1 & W2MadBanana wrote:ledfreak3d - just checked mine with Domoticz and the same as you, white doesn't work. I'd only previously used it by sending this ..
http://192.168.1.92/control?cmd=PWMFADE,3,500,5 - which lights the strip white, attached to W2
Not sure what to do in Domoticz though, RGB on the wheel works fine.
First create a dummy LightWave RF dimmer
second made a script_device_w1.lua script, or use LUA editor on Domoticz (don't forget to save as de device one)
Code: Select all
commandArray = {}
DomDevice = 'PWM_W1_LED_H801_ESPEASYFW'; --your dymmy LightWave RF Dimmer
IP = '192.168.0.196'; --change for your h801 ip
PIN = "4"; -- for w1 pin
if devicechanged[DomDevice] then
if(devicechanged[DomDevice]=='Off') then
DomValue = 0;
else
DomValue = otherdevices_svalues[DomDevice];
CalcValue = (DomValue-1) * 33;
end
if CalcValue==nil then CalcValue=0 end
runcommand = "curl 'http://" .. IP .. "/control?cmd=PWM," ..PIN.. "," .. CalcValue .. "'";
os.execute(runcommand);
print("PWM value= "..CalcValue);
end
return commandArray
Domoticz stable 3.5877 for real & Domoticz beta for test
Rfxtrxe / RFLink / Milight / Yeelight / Tasmota / MQTT / BLE / Zigate
http://domo-attitude.fr
Rfxtrxe / RFLink / Milight / Yeelight / Tasmota / MQTT / BLE / Zigate
http://domo-attitude.fr
-
- Posts: 25
- Joined: Thursday 13 October 2016 21:45
- Target OS: Raspberry Pi / ODroid
- Domoticz version: Stable
- Location: Kent, England
- Contact:
Re: [ESP8266] Commercial H801 WiFi RGB-dimmer topic
Thank you Deennoo, that's worked for me!
-
- Posts: 26
- Joined: Saturday 02 January 2016 2:22
- Target OS: Raspberry Pi / ODroid
- Domoticz version: beta
- Contact:
Re: [ESP8266] Commercial H801 WiFi RGB-dimmer topic
How does os.execute curl compare to the OpenURL command in speed?deennoo wrote:MadBanana wrote:ledfreak3dCode: Select all
... runcommand = "curl 'http://" .. IP .. "/control?cmd=PWM," ..PIN.. "," .. CalcValue .. "'"; ...
Edit: Should've just tested it. It's much faster. Script below updated.
This is my current script for driving my ESPEasy lights, including a way to simulate white on RGB-only strips. It also uses a curve to get higher resolution at the lower end, where the brightness changes are more noticeable.
Code: Select all
local lights = {
['Stuereol Spots'] = {ip = '192.168.33.61', pin = '14', rgb = false},
['Stuereol Skab'] = {ip = '192.168.33.61', pin = '4', rgb = false},
['Vitrineskab'] = {ip = '192.168.33.62', pin = '13', rgb = false},
['Kontorreol'] = {ip = '192.168.33.64', pin = '13', rgb = false},
['Skrivebord'] = {ip = '192.168.33.67', pin = '14', rgb = false},
['Sengelys'] = {ip = '192.168.33.66', pin = '14', rgb = false},
['Kontorhylde W'] = {ip = '192.168.33.67', red = '15', grn = '13', blu = '12', rgb = true},
['Stuereol W'] = {ip = '192.168.33.61', red = '15', grn = '13', blu = '12', rgb = true},
['Seng W'] = {ip = '192.168.33.66', red = '15', grn = '13', blu = '12', rgb = true}
}
function setlight (ip, pin, dvalue)
os.execute("curl 'http://" .. ip.. "/control?cmd=PWM,".. pin .."," .. tostring(dvalue) .. ",128'")
end
commandArray = {}
for deviceName,deviceValue in pairs(devicechanged) do
if (lights[deviceName]) then
if (deviceValue == 'Off') then
dvalue = 0
elseif (deviceValue == 'On') then
dvalue = 1024
else
inputValue = tonumber(otherdevices_svalues[deviceName])
curve = 1.5848931924611
normalizedCurVal = (inputValue - 1.0) / 99.0
rangedValue = (math.pow(normalizedCurVal, curve) * 1023.0) + 1.0
dvalue = math.ceil(rangedValue)
end
if (lights[deviceName]['rgb']) then
setlight(lights[deviceName]["ip"], lights[deviceName]["red"], dvalue)
setlight(lights[deviceName]["ip"], lights[deviceName]["grn"], dvalue)
setlight(lights[deviceName]["ip"], lights[deviceName]["blu"], dvalue)
else
setlight(lights[deviceName]["ip"], lights[deviceName]["pin"], dvalue)
end
end
end
return commandArray
-
- Posts: 65
- Joined: Tuesday 24 February 2015 15:54
- Target OS: Raspberry Pi / ODroid
- Domoticz version:
- Contact:
Re: [ESP8266] Commercial H801 WiFi RGB-dimmer topic
I was going to add code to the espeasy plugin to emulate a white milight device so wouldn't have to use scripts/user vars etc.
BUT found the milight hardware device in domoticz is very strange - changing the device mode from rgb to rgbw to white etc incorrectly creates new devices but the main problem is simply creating a milight hardware device and changing its mode to white results in a dimmer that doesn't work (doesn't send udp packets)! You have to change the mode to rgbw and rgb then back to white first?! Even then depending on the sequence it may end up sending different udp packets as the slider is adjusted. Also, only 32 steps for the milight dimmer...
Shame as it would have meant I could have got rid of my script to handle the white channel and also the uservar to work around the on "feature" of not sending the level...
commandArray = {};
IP = '192.168.2.165';
Port = '80';
GPIO = 3; -- r=0,g=1,b=2,w=3
DomDevice = 'Kitchen White Lights'
if devicechanged[DomDevice] then
if(devicechanged[DomDevice]=='Off') then
print("Turning OFF" .. DomDevice)
commandArray['OpenURL']="http://" .. IP .. ":" .. Port .. "/control?cmd=PWMFADE," .. tostring(GPIO) .. ",0,1"
elseif (devicechanged[DomDevice]=='On') then
print("Turning On with value : " .. tostring(uservariables[DomDevice]))
otherdevices_svalues[DomDevice] = tostring(uservariables[DomDevice])
commandArray['OpenURL']="http://" .. IP .. ":" .. Port .. "/control?cmd=PWMFADE," .. tostring(GPIO) .. "," .. tostring(tostring(uservariables[DomDevice]*10+23)) .. ",1"
else
print("Value sent from domoticz is : " .. otherdevices_svalues[DomDevice])
uservariables[DomDevice] = otherdevices_svalues[DomDevice]
commandArray['OpenURL']="http://" .. IP .. ":" .. Port .. "/control?cmd=PWMFADE," .. tostring(GPIO) .. "," .. tostring(tostring(uservariables[DomDevice]*10+23)) .. ",1"
commandArray['Variable:'..DomDevice] = uservariables[DomDevice]
end
end;
return commandArray
BUT found the milight hardware device in domoticz is very strange - changing the device mode from rgb to rgbw to white etc incorrectly creates new devices but the main problem is simply creating a milight hardware device and changing its mode to white results in a dimmer that doesn't work (doesn't send udp packets)! You have to change the mode to rgbw and rgb then back to white first?! Even then depending on the sequence it may end up sending different udp packets as the slider is adjusted. Also, only 32 steps for the milight dimmer...
Shame as it would have meant I could have got rid of my script to handle the white channel and also the uservar to work around the on "feature" of not sending the level...
commandArray = {};
IP = '192.168.2.165';
Port = '80';
GPIO = 3; -- r=0,g=1,b=2,w=3
DomDevice = 'Kitchen White Lights'
if devicechanged[DomDevice] then
if(devicechanged[DomDevice]=='Off') then
print("Turning OFF" .. DomDevice)
commandArray['OpenURL']="http://" .. IP .. ":" .. Port .. "/control?cmd=PWMFADE," .. tostring(GPIO) .. ",0,1"
elseif (devicechanged[DomDevice]=='On') then
print("Turning On with value : " .. tostring(uservariables[DomDevice]))
otherdevices_svalues[DomDevice] = tostring(uservariables[DomDevice])
commandArray['OpenURL']="http://" .. IP .. ":" .. Port .. "/control?cmd=PWMFADE," .. tostring(GPIO) .. "," .. tostring(tostring(uservariables[DomDevice]*10+23)) .. ",1"
else
print("Value sent from domoticz is : " .. otherdevices_svalues[DomDevice])
uservariables[DomDevice] = otherdevices_svalues[DomDevice]
commandArray['OpenURL']="http://" .. IP .. ":" .. Port .. "/control?cmd=PWMFADE," .. tostring(GPIO) .. "," .. tostring(tostring(uservariables[DomDevice]*10+23)) .. ",1"
commandArray['Variable:'..DomDevice] = uservariables[DomDevice]
end
end;
return commandArray
- ledfreak3d
- Posts: 98
- Joined: Sunday 01 November 2015 15:30
- Target OS: Linux
- Domoticz version: 3.8025
- Location: Hoorn
- Contact:
Re: [ESP8266] Commercial H801 WiFi RGB-dimmer topic
I still use quinors lua code for most of my dimmers because it has a realy nice dim function
would be great if that could be implemented for rgb and white control in esp easy under domoticz
would be great if that could be implemented for rgb and white control in esp easy under domoticz
Unleashe the magic smoke ;)
Who is online
Users browsing this forum: No registered users and 1 guest