Problem solved! I just re-flashed the Rfxtrx433E device with Ext firmware instead of Pro1. It is also possible that I missed to set the device in Run Mode in the RFX flash tool after previous flash. I don´t remember if I did and I don´t know if it would work at all if I forgot. But now it works just ...

Hi!
My Domoticz running on a Rpi 3 model B crashed a week ago. I replaced the microSD-card and reinstalled Domoticz. I also updated the fw in Rpi and the Rfxtrx433E. Since then my Byron SX PIR motion sensors does not seem to send proper signal. In the log-file it says "Error: RFXtrx433E: Invalid ...

zak45 wrote: Tuesday 25 September 2018 16:46 Or you can give a try here:
https://www.domoticz.com/wiki/Plugins/iCal.html

Could be an alternative for me. Have you got any examples of how this works?

Edit: Forget my last sentence I just had to keep reading the page you linked to

It didn´t work! Those paths are essential since it doesn´t work at all when I remove them.
I think that I will give up on this since it seems impossible for me to solve. Is there by any chance anyeone that has saved the full instruction how to do this. Bakseedas pdf:s are deleted so no luck ...

I have also tried now to change my files/rename them, and I get errors, but never the error that you had before, so no luck there.

No actually, my GCal3.json don´t look like that!

Here are mine.
{
"private_key_id": "deleted",
"private_key": "deleted like 10 rows ",
"client_email": "deleted ...

I have tried to check the credentials. No luck! I give up I think. Here is the content in the file "GCal3.json" Does your GCal3.json have the same content? Or is there any other file I should check out?

{
"type": "service_account",
"project_id": "deleted",
"private_key_id": "deleted",
"private ...

I will look into it!
But, the problem might be on your side rather than the script.
If I look at google´s api troubleshooting page it just refers Bad request error to "User error"
I guess it can be other errors on your side, maybe some of the other files.

Credential file? User variable with ...

I get the same issue with your file as well.
2018-09-24 20:17:33.969 Status: User: Admin initiated a switch command (35/GCalCheck calendarname/On)
2018-09-24 20:17:34.378 (RFXtrx433E) Temp (Inne b.v.)
2018-09-24 20:17:34.006 Status: LUA: GCal3 V 1.0.3: Calendar device GCal calendarname (idx:33 ...

You must be using the old file!
Because my log says V1.0.3 and your log says V1.0.2.
And you also have the same fail log/message as before.

Skickat från min SM-G950F via Tapatalk


I have tried to find the updated version but no luck since all the files are deleted from this forum. But I don´t ...

You must be using the old file!
Because my log says V1.0.3 and your log says V1.0.2.
And you also have the same fail log/message as before.

Skickat från min SM-G950F via Tapatalk


I have tried to find the updated version but no luck since all the files are deleted from this forum. But I don´t ...

What does the log say?




Here is my log:
2018-09-24 18:12:00.065 Status: LUA: GCal calendarname needs to run
2018-09-24 18:12:00.066 Status: EventSystem: Script event triggered: /home/pi/domoticz/scripts/lua/script_time_gcal.lua
2018-09-24 18:12:00.122 Status: LUA: GCal3 V 1.0.2: Calendar ...

Hi!
I have not found any solution unfortunaterly. Have given up on this! I just deleted the plugin since there is no support. Sorry! If you find a solution it would be nice if you could post your solution here :)


Hello again!

I think I have come up with a solution.
Atleast it did connect ...

Hello!
Is there still any support for this plugin? I can try at least to get som respons here :)

Today I replaced my Raspberry Pi with a new one and finally I got it all up and running. But unfortunately the script that checks my Google-calendar returns an error. I just can´t figure out what is ...

EdwinK wrote: Sunday 29 July 2018 19:14 He has quit Domoticz and is gone to another domotica system, so all his scripts have been removed from his github server.

Ok, thanks! That was unfortunate because I really could need some support. Anyone who has the files? Do they work smoothly?

Does anyone know what has happened with this project? I have encountered issues with my previous version of Gcal and tried to get some support in the old projects forum. No luck there :( Then I saw that Bakseeda started e new project here and has linked some documents on Github. The problem is ...

Does anyone know what has happened with this project? I have encountered issues with my previous version of Gcal and tried to get some support in the old projects forum. No luck there :( Then I saw that Bakseeda started e new project here and has linked some documents on Github. The problem is that ...

Hello!
Is there still any support for this plugin? I can try at least to get som respons here :)

Today I replaced my Raspberry Pi with a new one and finally I got it all up and running. But unfortunately the script that checks my Google-calendar returns an error. I just can´t figure out what is ...