Sry for bump, any advice?

Hi

I'm a bit unsure weather this is a Domoticz problem or what..

Feature
To send music from a LMS server to a Chromecast Audio with the help of a Domoticz http command

Setup
I have a Qnap NAS running LMS in a container. In LMS I have the plugin CastBridge. In Domoticz i have a dummy switch ...

Much needed, good job!

Nice, i could put device on/off but it will not work to change colors, or strength on light. Is there anymore modifications thats need to be done?

Dnpwwo wrote:@Boredcat,

@sweup,

If you are running the stable Domoticz version you won't see it because it isn't supported. If you are running the current beta it will show up as 'Denon AVR 4306'.

Thanks, i see that one. I thought that one was another, the example version.

Thanks for plugin

I followed the guide by installing from github, the folder and file is there but can't see it under the hardware tab. What name will it have there?

Thanks for reply, looking forward for this

Hi, i installed python (sudo apt-get install libpython3.4) but no plugin folder for me. Is there anything more that needs to be done?

Edit: seams that 2.7.9 us running. I dont understand second step: set (python_additional..)

Sry for noob question, but how should i wrote the proper command?

Someone got Magic Ufo to play nicely with domoticz (on/off, colors etc)? Would really appreciate some guidance if someone got it working.

Im using the Neo Coolcam power plug, the pairing was no problem but every 2 weeks its shutdown and i have to switch it on

I finally got this working by adding the cast bridge plugin in LMS settings. Thanks for help

First ip of the logitech media server, then change PLAYLISTNAME to the name of your playlist and then IPADDRESSPLAYER, ip address or MAC address to the player (chromecast)

http://IP:9002/status.html?p0=playlist&p1=play&p2=PLAYLISTNAME&p3=IPADDRESSPLAYER
Thanks really appreciate your help, the ...

Hi

Do you mind share how you setup your Alarm or/and Play music features? Looking for the smiliar setup, when motion detected and alarm is on = play siren on the chromecast with the help of LMS.

I created a dummy switch in domoticz called siren kitchen, then edited the switch so when it turns on ...

Hi

Do you mind share how you setup your Alarm or/and Play music features? Looking for the smiliar setup, when motion detected and alarm is on = play siren on the chromecast with the help of LMS.

@sweup
@justintime

Lets start from the beginning.... As i have a rather basic implementation with the support of Nayr!
I have the following setup:

3 PI's connected by wire seperate VLANs spread over multiple floors and cabinets... Using a Raspbian SDcard Image as a basic startingpoint, with ...

Thanks. Domofence switch seams to work but I don't get my alarm switch to be turned on. Does this Blockly seams ok?

I got two geofence, so "when geofence 1 and geofence 2 is on, larm should be switched on". I got a similar one for "off", bad approach?

This is how I switch my 'Somebody home ...

I want to flip "on/off" commands when both my and my wifes phone is in/outside the geofence - possible?

Personally I use three virtual switches. One for me and one for my wife. These are switched by crossing the geofence.
Then I have a third virtual switch 'Anybody home' and I switch the third ...

I want to flip "on/off" commands when both my and my wifes phone is in/outside the geofence - possible?

Looking at my setup: Your mqtt port is set to 23 (telnet), mine is 1883(default MQTT port i believe).
The telnet port in the htc-settings is correct, thats the port it communicates with the Pioneer Reciever, btw are you sure its 23, min VSX920 has 8102.

Also need to set it up again, had a few ...

This is a bit out of my league but really wants this work. I have follow the installation procedures but don't get any effect on the AVR. Hoping that someone could point me in the right direction.

The MQTT switch using my AVR IP-number. Right? What usr/psw?, right now domoticzs credentials - doesnt ...