Search found 8 matches
- Thursday 17 March 2016 16:26
- Forum: Z-Wave
- Topic: Eurotronic Comet z-wave Thermostat does not seem to work
- Replies: 40
- Views: 10673
Re: Eurotronic Comet z-wave Thermostat does not seem to work
So now, when it's getting warmer outside my TRV went completely crazy. Today it went up to 28 degrees despite the fact that both modes were set to 16. I'm still looking at how to control in manually (REMO mode), so I could use external thermometer inside the room to control valve opening. I;m ...
- Friday 05 February 2016 17:22
- Forum: Z-Wave
- Topic: Eurotronic Comet z-wave Thermostat does not seem to work
- Replies: 40
- Views: 10673
Re: Eurotronic Comet z-wave Thermostat does not seem to work
I also have this TRV and got it to work... well, kind of. First, couple of basic things. If you read the manual you will learn some stuff there ;) : z-wave commands: https://photos-3.dropbox.com/t/2/AABTc7THYFcZenux8IzSZtxHfRPL54ln_yA9Nfv8nP5mPA/12/516430/png/32x32/1/_/1/2/Screenshot%202016-02-05 ...
- Saturday 16 January 2016 15:52
- Forum: Heating/cooling
- Topic: StellaZ vs Danfoss Living connect vs Komforthaus Comet ?
- Replies: 43
- Views: 9542
Re: StellaZ vs Danfoss Living connect vs Komforthaus Comet ?
I have no experience with Danfoss.
Comet Z is also EUROtronic product - it's actually next generation of StellaZ. Comparing to Danfoss it can report temperature from sensor. I have one and I;m currently experimenting with it. so I will have some feedback in couple of days.
Comet Z is also EUROtronic product - it's actually next generation of StellaZ. Comparing to Danfoss it can report temperature from sensor. I have one and I;m currently experimenting with it. so I will have some feedback in couple of days.
- Thursday 07 January 2016 21:32
- Forum: Z-Wave
- Topic: Please help a newbie out - Zwave - Domoticz / Devices? :?
- Replies: 6
- Views: 3259
Re: Please help a newbie out - Zwave - Domoticz / Devices? :
This sensor has tamper detection and input e.g. 1wire temp sensor. It's hard to say what connector was deiscoverd as second device without actually checkingpvm wrote:I think the second switch is the tamper detection.
- Thursday 07 January 2016 21:21
- Forum: Z-Wave
- Topic: Figaro FGD211 not able to install on Domoticz Raspberry Pi
- Replies: 1
- Views: 644
Re: Figaro FGD211 not able to install on Domoticz Raspberry
Can you install other, not Fibaro series modules? Did you enabled accepting new hardware?
- Thursday 07 January 2016 20:51
- Forum: Z-Wave
- Topic: fibaro fgk 10
- Replies: 1
- Views: 691
Re: fibaro fgk 10
Why are you attaching screenshot in MS doc, it's ridiculous. Answering your question: battery powered sensors are reporting to controller by some interval. You need to change the interval. But it shuld report every time sensor is triggered apart fro interval setting, so there is little sense ...
- Thursday 07 January 2016 13:02
- Forum: Z-Wave
- Topic: Can't include devices anymore
- Replies: 20
- Views: 6094
Re: Can't include devices anymore
I had the same problem, I couldn't include anything from do oicz. I used ozw panel and all worked. Must be some problem wih Domoticz itself
- Tuesday 29 December 2015 22:43
- Forum: Language / Translation
- Topic: Polish-pl
- Replies: 7
- Views: 8236
Re: Polish-pl
Hi,
I just started reviewing and correcting polish translation to comply with software translation rules. I think I should be done by the end of the weekend.
Don't be surprised with many changes I'm trying to use all my translation experience (10+ years), but my skills are little rusty now
I just started reviewing and correcting polish translation to comply with software translation rules. I think I should be done by the end of the weekend.
Don't be surprised with many changes I'm trying to use all my translation experience (10+ years), but my skills are little rusty now