Antwan, I see you have R-pi also, not worried about the frequent write-operations to SD card ????

I've had HW-failure on my SE-3000 comm-interface, new card was installed few months ago, with that new firmware...since then previous method of Domoticz scraping data (port 2222 & Fwd to solaredge.com ) doesn't work anymore. Probably due to SE update/version on newly installed interface board.
As ...

@Egregius:

do you run your script from the general(S1) switch only?
As mentioned before, I activate script on both S2,S3. I observe in the log that a command on either switch triggers the script, then probably the script re-confirmes the command on the other switch, which is seen as a devicechange ...

I've tried to 'fool-prove' this script, just by clicking around like a madman :twisted:

When the script is attached to the general input only (i1), I found it still possible to get 'unsynched'.
I've not been able sofar to get unsynched when I insert script in on/off actions for both the switches ...

Finally!!!

(the 14 should have worked...maybe was not patient enough when testing)
so for others: the decimal node ID on the ZWavew hardware panel, e.g.: 014 (0x0e)

It seems working now, I'm so relieved!
Now status is updated correctly (not instantly, but within acceptable time-frame; few secs on ...

1st line in my script needs to be:
#!/usr/bin/php 5
now scripts execute.

Node state doesn't refresh yet...perhaps node identification not right.
the 3 available switches on the 2relay-qubino are in device list with following ID's:
0000E01, 0000E02, 0000E03
tried node 'E', 'E0', 'E01', '14' no ...

pi@domoticzpi /usr/bin/php $ chmod 755 /usr/bin/php
pi@domoticzpi /usr/bin/php $ ls -l
total 12
-rwxrwxrwx 1 pi root 327 Jul 18 01:53 extract.php
-rwxrwxrwx 1 root root 415 Jul 14 00:47 Q2_14.php
-rwxrwxrwx 1 root root 400 Jul 9 00:12 Q2_xx.php
pi@domoticzpi /usr/bin/php $ ./extract.php
-bash ...

Dear Kriss/All

your instruction #2: 'Make sure script starts with: #!/usr/bin/php'
made me advance a step, thx for that!
But now I get another error-indication; it now seems the php to be called succesfully, however, my new problem is with permission to run the script.

I've set the scripts to ...

Dear experts,

I'm a newby to linux, so forgive me for asking stupid questions ;-)

I came down to the point that I need to use the refresh to get device statuses correct for my 2relay Qubino modules.

I do have some trouble how to use the offered script.
I've installed apache2 and php5 (apt-get ...

I'm also very interested in listening in to Powermax nodes as well!
I'm thinking of same use-cases as you mention.

I have the visionic protocol enabled in RFXtrx433E, but in general it hears nothing from my Powermax or it's sensors. It has captured only one event since on, 1 device had appeared in ...

after few hours still no change, in the meantime was struggling with WU, got stuck somewhere; rebooted, during which Domoticz seemed to fail (long time until state reported running); after being back, the solaredge devices are there:
-lifetime kWh
-DC Voltage
-AC Voltage
-inverter Temp
-Frequency ...

My Domoticz = 2.2025

-Forwarding of data is working, the solaredge portal is showing current values and (just a little little today ) energy production since sunrise.
-No new devices are showing for the inverter.

Ideas what could be wrong?

Hi All,

I have SE3000,
Changed server adress in SE to my raspberry ip 192.168.1.x (left port unchanged).
In Domoticz, changed remote address to prod.solaredge.com , port to 22222 .

I get the following events in log:
Sat Jan 31 22:09:21 2015 Error: SolarEdge: Unknown Type: 1408
Sat Jan 31 22:09:21 ...