Hi guys,

Can I consult databases of components like:
P1-port (el and Gas)
Z-wave powerswitch

I would like to export and back-up them.
If possible do some calculations in excell.

Thank you!

Grtz,
Mathias

Hi Firewizard,

It Works!!

Thank you verry much!!

Hi Erem and Firewizard, The WinSCP wat a great tip. now I understand better what i'm doing in the pi. I Think I installed everythin, I followd the manual on github. I had connection between the pi and SMA. Now , I hope to see the SBF-spot-sensor working on domoticz tomorrow!! I read there where ...

Hi Fire-wizzard I tried to install the SBF-spot again (V3.7.1) I did the update and upgrade, I re-installed de wget (was already installed) Still the same problem: " mdb@Domoticz:~ $ sudo wget https://github.com/SBFspot/SBFspot/archive/V3.7.1.tar.gz --2021-02-05 16:35:35-- https://github.com/SBFspot ...

Thank You FireWizard!

But no succes...
I don't know what else to try ...
I think my knowledge of linux is lacking...

thanks anyway!!

Grtz!

Hi, Now I noticed that I can download the files using google chroom on my desktop, (this morning it went wrong even on the desktop) But when I try to download the sourcecode with the Pi, i still get the notification that the netwerk is unreachable. I rebooted the pi and tried again, same problem ...

Hi FireWizard,

I use the same site, URL (by clickin on sourcecode (tar.gz): command:
"wget https://codeload.github.com/SBFspot/SBF ... .gz/V3.7.0"

But i get message 443...failed: The network is unreachable.
Can you give me the exact command?

Grtz!

Hi guys, I want to integrate my sunnyboy 3.6 into my domticz system. I am following the instructions on github and everything goes well, untlill I have to download the latest version of the sourcecode of sbfspot: "failed:The network is unreachable." I tried many differtent options by chaniging the ...

Hi Guys,

My 2 Z-wave nodes with batteries (molitesensor and 2-pole switch from benext) do not automatically send temperature updates. (only if I wake them up manually)
The wake-up time is set to 300s.

The same value is always repeated.

Anyone idea's?

Thanks in advance

Grtz,
Mathias

Hi FireWizard,

Fluvius confirms that the P1-port is opend.
They don't mension that you still have to log in on there website to switch a slider-button to open the port again.

But that i figured out a while ago...

Regards

Hi, guys,

I really don't know what I did, but the code "sudo cu -l /dev/ttyUSB0 -s 115200 --parity=none -E q" gives readable vallues for the first time!
After rebooting the pi, i can find the device in domoticz to!

I hope it stays this way!

Thank you guys!

Hi Ropske,

I have the FTDI Ltd FT232 Serial (UART) IC cable from robbshop.

I hope this is the right one?

Hi FireWizard, The type is Siconia. I followed all the steps above without any results. Normally the P1-port is available ( I did the stuff i had to do to open it by fluvius) But i do doubt that the meter is sending any data. Unfortunitly, I do not have a pc with a serial port available. I tried in ...

Hi Ropske,

I already did that. I opend the port also online with the slider button.
Normally this is not the problem.

Thank you for your advice!

How can I be shure i recieve data? Control with laptop,...?

okay, thanks,

I'm sure its DSMR5 , so baudrate should be 115200?
I changed de parity to "even", are there other options?
the pi respondend again "connected"
is it normal I'm blocked after this? I have to abbord the sesion and start again with putty.

Maybe I have a problem with the DSMR-version.

Witch code I have tu use to change the DSMR-version?

Hi,

I installed de cu.
When i trie the code "sudo cu -l /dev/ttyUSB0 -s 115200 --parity=none -E q" now,
The pi answers "connected"

one step closer

Hi, I stopt domoticz, I did dmesg to find the port name: usb 1-1.3: FTDI USB serial device converter now attached to ttyUSB0 So the port is ttyUSB0, i assume. I tried the code. sudo chmod 666 /dev/ttyUSB0 : no reaction noticeble on the pi (that's a good sign?) sudo cu -l /dev/ttyUSB0 -s 115200 ...

Hi FireWizard,

The PI runs Domoticz V4.10717