With changing the Poll Interval from 10 seconds to 30 seconds, the connection is still working after aprox. 48 hours

I just noticed when I re-start the Enphase hardware in Domoticz it throws also an error 'Error getting http data! (power)'. But it does this only the first time when it collects data.

Hi Gizmocuz, thank you for your reply. Domoticz is the only system talking to Enphase. But the polling interval has been set to 10 seconds. Let me try to set it back to 30 seconds and see if that makes a difference. For me the communication worked since I got my solar panels last year, but after a ...

Since about a week I have a similar issue with my Domoticz connection with the Enphase controller. After some time Domoticz will not update values anymore and throw the error 'Invalid data received! (no session_id)'. When I disable the Enphase hardware in Domoticz and start it again it will work for ...

I am using firmware ZW164_Siren 6_EU_V1_06. The volume and tones are not configurable via Domoticz , but if you pre-set them as described by yourself earlier in this post using Z-Wave PC Controller then it is usable. Domoticz creates 8 different buttons to trigger 8 different sounds which all ...

I am using firmware ZW164_Siren 6_EU_V1_06. The volume and tones are not configurable via Domoticz, but if you pre-set them as described by yourself earlier in this post using Z-Wave PC Controller then it is usable. Domoticz creates 8 different buttons to trigger 8 different sounds which all ...

Today @GIZMOCUZ reached out to me that my suggested modification (other thread) had been implemented in the new Betá (14016). You can imagine that I could not wait to try. So I upgraded my Domoticz install.... after the reboot gave it a try...... and it worked !!!! When pressing one of the sound ...

I updated Domoticz today to the latets beta, did load the new firmware on the Doorbell/Alarm 6, excluded and included the device but there is no difference. It still does not work.

Hi ZachariahVance, which idx number are you using from the device ? I am also trying for a while to have the Doorbell/Sirene v6 play with a command from Domoticz but without luck so far. The current values screen for my setup is grayed out and does not have a play ringtone option. Could you share ...

in openzwave.cpp, SwitchLight() there is an explicit, hard coded hack, for Aeotec Doorbell 6 only, to set the device's value to the 32nd entry (index 31) from the list of available entries when the device is switched "on" (value = 0xFF (255)). The 32nd entry is according to the comments with that ...

Probably many of you already know this, but it took me a while to figure out so I thought maybe it is worth to share for those who don’t know yet. For some weeks I am trying to get the Aeotec Indoor Siren 6 to work on Domoticz. When the device has been added to Domoticz it provides entries with q ...

Did anyone find a solution/work around for this ? I was able to reduce the volume using "Zwave PC Controller 5" but I am still not able to operate the Alarm 6/Doorbell 6 from within Domiticz. I tried to bypass Domoticz by using ozwcp but running 2 open z wave drivers at the same time does not work ...

I use the same method as rgroothuis. Normally the In-Lite hub is controlled with an illumination sensor, but when you disable this you can switch it on/off with a 220v Z-Wave switch and control it within Domoticz. You only can switch the whole In-lite hub on/off but not the sepearate groups within ...

Better not to rely on the "Test Verbinding" option. I have 2 Dahua camera's also and they are connected to Domoticz. For the imageURL I use : cgi-bin/snapshot.cgi?Channel=0 Maybe worth to give that a try. My other settings are similar to yours. The camera screen on the dashboard of Domoticz is so ...